Search results

Search the forum Search Articles
  1. maine04max

    Head studs ?

    whats everyone's opinion on upgrading to aged 625 studs versus going to the 14 mm option ? I'm not even sure how to get the 14mm studs can't seem to even find a part number
  2. maine04max

    Input needed for race truck setup

    I recently picked up a 2004 silverado 1500 4wd regular cab shortbed truck . the plan is to remove the motor and trans from my current truck and put into the 1/2 ton . the truck has dyno'd 860 rwhp on fuel only and 1162 rwhp on spray . we recently put all billet parts in the allison and are...
  3. maine04max

    Help: low lift psi

    I posted in another thread but thought i would start one of my own . I just finished installing dual cp3's two days ago . I have been running an air dog 165 for 2 plus yrs , no upgraded pick up . today I installed a glow shift 30 psi fuel press gauge and noticed it was sitting at 5 psi @...
  4. maine04max

    Finally a low 11 time slip

    all truck nationals @ new england dragway today best time slip of the day 60 1.737 330 4.761 1/8 7.300 mph 96.14 1000 9.514 1/4 11.390 mph 120.03 xko4heiCy3A more videos to come
  5. maine04max

    New look for the truck

    I made a few changes to the look of the truck . next thing I need to do is get it lowered a few inches
  6. maine04max

    Sand drags

    A few friends and I went to hunneywell valley this past weekend . I ended up wining 1 first place for radar runs and 2 first places for sand drags . In radar i got 58 mph in 300 ft on a loose track . the one time I looked speedo was @100 mph at the end of the 300 ft ( spinning of course )...
  7. maine04max

    airdog 165II vs airdog 250

    I have a chance to trade my 165 for a 250 . I know the 250 is worth more but do you guys think its worth the effort to change over? iirc the 250 is not adjustable , and dont want issues down the road .
  8. maine04max

    Question: Aftermarket turbo drain

    does anyone sell a aftermarket drain for an S300 turbo ? the drain that came with my htt turbo was a modded stocker and it isnt the ideal setup .
  9. maine04max

    Question: 5 speed valve body wiring

    anyone know where the best place to buy the wiring harness for the valve body? and possibly the big round plug on pass rear of trans that can be spliced in?
  10. maine04max

    Cummins issues

    A buddy of mine has a 12v . a performance rebuild was done less than 10k miles ago. specs are 64 /475 twins , .020 marine pistons @15/1 with valve reliefs ,scheid small cam & 150# springs , fire ringed and dyno @ 650 hp. we have not measured everything yet , but I thought I would put up some...
  11. maine04max

    Compressor wheels

    Do any of the more experienced guys have thoughts on these new s300 etr wheels? my setup is twins with htt66 ss16cm with s480 and both have race covers . I have toyed with the idea of getting a new 66 etr wheel or maybe changing the 480 wheel to a billet etr wheel if they even make one ...
  12. maine04max

    Question: thoughts on hoosiers

    thoughts on these Hoosiers 33 /12 x 16 bias plys http://www.summitracing.com/parts/HOO-18975/ forgetting the price is a bias ply ok seems like a good option for a tall tire and rpm issues running over 120mph with a 5 speed
  13. maine04max

    eight turbos ???

    bLfujQrr2yA the car is called the Inciner8or
  14. maine04max

    Good News and Bad :(

    well good news got my 11 second run I was after . 60 2.025 330 5.159 1/8 7.712 mph 94.54 1000 9.902 1/4 11.749 mph 121.66 Bad News looks like I may have blown out my rear main seal . oil looks like it is leaking between rear adapter and bell housing
  15. maine04max

    Help: suspention sugestions form dragracers

    I take it there isn't a set rule for suspension setup on all trucks . I have gone back and read a few threads on caltracs stuff . before mine were set on lowest hole . clamps and ranchos on setting 9 . I know my 20's are not helping me but I set caltacs on highest hole took off the clamps...
  16. maine04max

    12.11 @119mph video

    Here is my video from 10/23/10 Fi6mVhf3LjE 60' 1.859 330 5.314 1/8 7.965 mph 93.15 1000 10.223 1/4 12.116 mph 119.19 was cold out about 42 degrees and pavement showed 33 degrees traction was an issue and as you can see I definitely need more fuel plan is...
  17. maine04max

    Hit the 1/4 mile

    finally got a chance to go to a 1/4 mile track first run left very soft maybe 1500 rpm 60 ' 2.025 330 5.350 1/8 8.073 mph 90.18 1000 10.436 1/4 12.439 mph 112.45 2nd run little harder 1900 rpm or so 60 ' 1.789 330...
  18. maine04max

    new Numbers for this year

    this is my new dyno sheet done this weekend at a local dyno event .
  19. maine04max

    Question: Socal balancer

    is there a trick to get the balancer on ?????? I checked the measurements on the key and key way and that looks good but it doesn't want to slide on to easy
  20. maine04max

    Help: Lb7 injectors

    anyone have a good connection on injectors? as many of you know im in the process of putting in a new engine . now it seems i wont be able to reuse my old injectors , the truck is hazing bad (white smoke) doesnt smell like antifreeze . i havent checked the oil level yet but plan to in...
Top Bottom