LMM: LMM with 222,000 tear down rebuild

Chevy1925

Chevy1925

don't know sh!t about IFS
Staff member
Oct 21, 2009
21,637
5,777
113
Phoenix Az
malibu795 said:
Have fill the crankcase up for that to happen... Talking 6-6-7 gallons of fluid..
Click to expand...

unless the crossover cracked into a bolt hole connected to it. then it would just weep out the head of the bolt since the mid plate is rtv'ed to the back of the block and around the bolt holes. looking at the mid plate on teh block side, if an o-ring let loose, it would leak out one side or the other through some open areas casted in so i dont see it getting through a bolt hold.
 
malibu795

malibu795

misspeelleerr
Apr 28, 2007
8,201
526
113
42
in the buckeye state
Chevy1925 said:
unless the crossover cracked into a bolt hole connected to it. then it would just weep out the head of the bolt since the mid plate is rtv'ed to the back of the block and around the bolt holes. looking at the mid plate on teh block side, if an o-ring let loose, it would leak out one side or the other through some open areas casted in so i dont see it getting through a bolt hold.
Click to expand...
O rings are or were good until I removed them... Gues I'll build a blocking plate and pressure test the cross over... I think 175psi should show up somewhere
jlawles2 said:
Thats one funny looking sling pattern there. Are you certain it was coolant? What did you use for assembly lube? Was there any lube in that rear main when you installed it?
Click to expand...
All this happened recently... Seals go on dry
 
M.A.M.

M.A.M.

Member
Jan 9, 2016
429
7
18
Ohio
Mine always go on with RightStuff.

How much coolant loss were you seeing?


Sent from my iPhone using Tapatalk
 
Fingers

Fingers

Village Idiot
Vendor/Sponsor
Apr 1, 2008
1,715
86
48
White Oak, PA
Some of the cover plate bolts get close, if not into the water jacket on the block. Did any of the bolts have coolant residue on their threads?
 
M.A.M.

M.A.M.

Member
Jan 9, 2016
429
7
18
Ohio
Yeah that's a lot. About the same as mine was with pinholes in one head...


Sent from my iPhone using Tapatalk
 
malibu795

malibu795

misspeelleerr
Apr 28, 2007
8,201
526
113
42
in the buckeye state
:confused: #1/#2 at the bottom
22770765_10213254136961536_5800076273586997023_o.jpg
 
J

jlawles2

Well-known member
Jan 28, 2010
1,056
39
48
Danbury, TX
Ouch that's gotta hurt. What block number is that for the year and for the truck?

Are you going to put another one in it to make the end of the year or focus on the Mutt?
 
malibu795

malibu795

misspeelleerr
Apr 28, 2007
8,201
526
113
42
in the buckeye state
M.A.M. said:
Is this the block that had a crank broken in it, or holed a piston?


Sent from my iPhone using Tapatalk
Click to expand...

Neither block... got installed December 2015...been ringed twice and bearings once,
And yes all in on the FL60.. I'm not sure what's in store for this truck... 478k of hard miles on the chassis it's not worth much. Get more out of a part out or repowering something with it... Or sled/drag truck
 
You must log in or register to reply here.
Top Bottom