Search results
-
July 10th Event
I am only planning to be there for Sat. Hope to meet up with some of you guys there. Sadly the think the HG's gave out on the truck so it will be in the driveway awaiting the funds to repair.- Krazykid
- Post #8
- Forum: Southern Members
-
July 10th Event
I am just going to watch as well, just seeing how many of the guys/gals on here had plans to attend?- Krazykid
- Post #4
- Forum: Southern Members
-
July 10th Event
Anyone going to the NHRDA event in Commerce, GA this weekend?- Krazykid
- Thread
- Replies: 12
- Forum: Southern Members
-
LLY injector leak
I like this idea.........what suggestions do you have for clean that area? Lots of shop towels!? -
LLY injector leak
So if I am looking at similar build up around this injector. I'm guessing a few hours of removing replacing the o ring and copper ring re install and all should be good? -
-
LLY injector leak
After reading this Tread, I just out checking around the truck and notice that I have just about the same problem. Seems that the #1 Injector is giving some sort of problems. I have not have time yet to check balance rates, but just checking visually, 7 of the eight injector tops were dry with... -
Installing a electric water pump
Could you please take some pictures of this process? For some reason I am having a hard time picturing in my mind where all these T's and splices are happening. Sounds like a great project.- Krazykid
- Post #33
- Forum: Duramax Hard Parts
-
Rear Brake Rotor Removal Question
Thanks guys......I know I don't have a "BMFDBH" but the small one that I do have I beat the Sh*t out of the drum and no go? Of course I only tried one side.- Krazykid
- Post #4
- Forum: Fluids and Maintenance
-
Rear Brake Rotor Removal Question
How? I got the brake caliper off but the rotor won't budge? Front rotors came right off with no issue. Is there something that I have to do to the e-brake? Thanks for the help.....- Krazykid
- Thread
- Replies: 14
- Forum: Fluids and Maintenance
-
Freaking ISPs. Check your internet bill!
:confused: I pinged a couple different servers with the speedtest.net and got different reports . Pinging Asheville, NC (less than 45mins drive) 3.79d .91u Pinging Atlanta, GA (more than 3 hours drive) 5.75d .92u Not 100% sure of the service my wife has opted for.- Krazykid
- Post #25
- Forum: Smoke Signals
-
Happy Birthday TrentNell!!
Happy Birthday! :birthday2: :b-day:- Krazykid
- Post #15
- Forum: Smoke Signals
-
Head Gaskets or Injector Cups?
when it's all said and done, you will be $broke$! :spit:- Krazykid
- Post #9
- Forum: Duramax Hard Parts
-
Your Favorite Tools
New favorite tool: Topside creeper. I now kind of look forward to do the head gaskets on the truck, just to use my new tools. :rofl:- Krazykid
- Post #49
- Forum: The Tool Crib
-
LLY: CP3 pump rebuild
Has anyone rebuilt thier own CP3 pump? I have seen a seals and bearing kit on Wicked Diesels website, is this a difficult project? -
LLY: Ahhhh....Motor Frustration!
Guys, thank you for the information.....I'm guessing that I will proceed witht he head gasket project and while I have the top of the motor apart I might as well pull the CP3...... -
LLY: Ahhhh....Motor Frustration!
So, if I am understanding this correctly, The head gaskets are the only cause of the hard rad hose on the LLY's? In addition to the head gaskets the CP3 which I have been suspect is weak for over a year now, Now is leaking fuel into the CC some how? The oil is dripping from the oil drain... -
LLY: Ahhhh....Motor Frustration!
I would say yes, however there is a VERY slight give. But overall I would call it rock hard. -
LLY: Ahhhh....Motor Frustration!
I am just now noticing/watching the oil level as I just found today oil drops under the truck near the oil drain plug. The upper rad hose was noticed a few weeks ago it was staying pressurized once the truck was cooled down. I'm just really confused as to what is going on with my truck. I'm...