LLY: Died in intersection!!

[snowman]

So a buddy of mine had his truck die in the middle of the intersection and wouldn't start. Got it towed to the shop and what do know!! it starts great. His banks iq showed these codes: P0193, P0405, P0642, P1093. So far nothing found. So we unplugged all the banks stuff. No codes yet! What you guys think??

 

[Maricopaagent]

My Edge did that on my 02.. every now and then, fall on its face.. What a pos..

 

[snowman]

i'll see what he says in the moning!! don't like that plug and play shit!

 

[snowman]

so fired it up today. blue smoke out the pipes and lopes. checked the harness and can't seem to find anything. Is there a specific spot they tend to rub through?? And i can't get a scan tool till monday morning!! any help would be great thanks!!

 

[Fastorange]

Edge fixed that... they had an issue with lb7 trucks.... If i were you i would call edge and see if they can help you with that...

 

[snowman]

sorry forgot to mention that it has full banks kit. IQ with six gun, exhaust, and intake.

 

[snowman]

ok so i got the truck into the shop. it fired up and drove! bearly!! it smoked blue like crazy! but still ran. The smoke smelled like two stroke oil and gas so i popped the fuel cap and what do i find!! Gasoline in the tank!! Drained the tank, dropped it, wiped it out by hand, then blew out the fuel lines from the engine back. Threw out fuel filter, put a new one on. Removed lines from filter housing, and let drain. Removed plugs from fuel rails, and let drain. When i had to relief valve out i decided to shim it. I made up a shim pack out of 3 small washers, and then reinstalled. Filled new filter up with fresh diesel, filled tank quarter full. Primed the crap out of the truck till i couldn't get anymore air out of it. Tried to start and no go, not even a try!! I cracked some lines and pumped some more, i even pressurized the fuel tank!! STILL NO START!! I disconnected anything to do with the glow plugs and gave it a small shot of ether and still no go! only ran on the ether. I'm getting fuel everywhere, and it's not even trying!! What gives?? Any help would be greatly appreciated!!!

If installing a shim in the relief valve can you over shim it and cause a problem??

 

[JustinD]

Gas will do that, we had an 03 LB7 that the owner filled with gas by mistake and it ended up needing all 8 injectors, started fine after that.

 

[Dirtymaxx03]

could have done some serious damage to the injection system. Are you sure its priming up. Sometimes you gotta pump that primer for freakin hours

 

[snowman]

i have been pumping it for hours!! i running out of things to do! i would love to put a scanner on it and see what everything is doing but i can't seem to get ahold of one.

I really hope it doesn't need injectors, i know the guy and he really doesn't need this right now.

 

[1953drtelco]

I'd be contacting the station that had gas in their diesel tanks....I'm sure your buddies truck wasn't the only victim.

 

[Atouchofgrass]

First start by letting the gas station know, second i would not use anymore ether. Make sure all those fittings on the rails are TIGHT. How long have you been trying to crank it over?

 

[snowman]

been trying it for a long time. have the charger on it. i'm getting fuel everywhere!! but still no fire.

got a scan tool today. put it on and i keep getting P0193 code. I checked the desired frp and its suppose to be 40 MPa and during cranking the actual is 2 MPa. so i'm not getting my rail pressure high enough to fire right?? How can i test or check the CP3 if it's building the proper pressure?? Please help! Need to get this truck running!!

 

[snowman]

bump!! just some input needed!!