Search results

Search the forum Search Articles
  1. Gmclbz

    Allison 5sp: Core 5 speed worth?

    What is a 5 speed core and converter worth these days?
  2. Gmclbz

    Question: 5500 question

    Looking for opinions/thoughts...what is a 2005 5500 worth? Truck has 160k on it, it is pretty clean (no rust other than minimal amount on chassis, has 4x4, pintle hook, gooseneck hitch, aluminum flatbed (nice condition). Tires are fair and would pass inspection with no issue. What do you guys...
  3. Gmclbz

    LBZ: 2 Dead ecms

    Anyone had any issues with the November release? I have 2 dead Lbz ecms. Both times with each ecm were exited during erasing with the $0101. Neither ecm will start or come back. Have tried 7.5, unhooking batteries, etc. Can still read tcm, but unable to even detect ecm? Anybody have any...
  4. Gmclbz

    4.8 Tuning

    Does anyone know if cats can be removed from a 2000 4.8 and still New York inspection. Nevermind the visual part, I'm talking only the computer stuff...If they can be removed what is need in tuning to keep CEL off?
  5. Gmclbz

    Info: Gt4718

    Anyone ever ran a Gt4718 as a single? Kinda been thinking a bit about it and curious how lazy it would be with the T6 housing...Not sure if a T4 is even available for it either. Thoughts? This is not a DD, only driven about 5k miles a year and does not tow ever.
  6. Gmclbz

    LBZ: Lbz not fueling

    Trying to figure out a problem with an 06' Lbz. S-400 and new injectors with 60% nozzles were just installed. Truck will not fuel past 40mm3 at all. Also there are no codes related to this issue. Truck ran and ran well before this. Truck sounds and idles good, balance rates are also good...
    • Gmclbz
    • Thread
    • Replies: 72
    • Forum: LBZ
  7. Gmclbz

    LBZ: Front cover and Assy. brackets

    Anyone know if there is any difference between LB7, LLY, LBZ front covers and Assy. brackets?
  8. Gmclbz

    LLY: Rough @ idle and below 2K

    Working on an 04.5 LLY with 115k miles on it, all stock. According to EFI #3 cylinder has a balance rate of +15. Tried icepick method and then replaced #2 and #7 harness with no change what so ever. Also checked harness @ FICM. Does anyone have any other ideas? There is no smoke and no blow by...
  9. Gmclbz

    1/8th mile 2night @ Owego 10-7

    Heading to Owego tonight around 5pm for probably the last Test and Tune. Anyone who wants to go, let me know. Sorry for the short notice as always. http://www.skyviewdrags.com/
  10. Gmclbz

    11.57 @ 116

    Made to the track today for the first time this year. Made 4 passes 2 of which were garbage. Can't complain for a stock bottom end.:D First pass: 11.58 @ 116.88 1.66 60' Second pass:
  11. Gmclbz

    LB7: Injector Cups

    Maybe this question has been asked, it may be a stupid question...has anyone ever tried green Loctite to seal injector cups? The green Loctite is a sleeve retainer. Just a thought or maybe I am way off base here...just thinking out loud.
  12. Gmclbz

    LBZ: A/C Delete

    Does anyone know of a place to get "caps" for the fittings at the firewall for an A/C delete?
  13. Gmclbz

    General Grabber for Pulling???

    What do you guys think of these? I may try them next year, just haven't decided yet... http://www.discounttiredirect.com/direct/findTireDetail.do?pc=32832&counter=5&ar=1250&rd=17&sw=false&cs=33
  14. Gmclbz

    4th Gear Sucks.....

    5th place, should stayed in 3rd...18 ft off of 1st place.
  15. Gmclbz

    New Track Times

    I finally had a chance today to make it back to Esta for a tnt, had a great day. Every pass but one was an 11.XX and didn't break anything. Best pass of the day was an 11.77 @ 114 mph. My 60's were a little on the high side. I feel it has 11.50's in it. Man does it feel good to break into the...
  16. Gmclbz

    LLY: P2227

    Can anyone shed some light on this DTC? Keep getting one on an 04.5 LLY with 150k. Any thoughts? Also will it cause a limp?
  17. Gmclbz

    Last weekends pull

    Cincinnatus, NY May 30th Good for 2nd place, I lost to a dodge...and yes I missed neutral at the end.:D http://www.youtube.com/watch?v=C7-QOFQfJwA
  18. Gmclbz

    New track times

    Unfortunately 1/8 but I was pretty happy after a few good passes tonight. Ended up with a 7.49 @ 90 with a 1.60 60' and backed it up with a 7.50 @ 90 with a 1.59 60'. Time to get back to the 1/4.....
  19. Gmclbz

    LB7: Fpr

    What type of issues other than an erratic idle could a bad FPR cause? Is it possible it could cause a severe drop in rail pressure?
  20. Gmclbz

    12.01@112

    Went to the track yesterday for the first time since late last fall. Disappointment again...did end up with a new best but still not quite what I was shooting for. I think the truck has it in it, but the driver sucks!:D Paint, I feel your pain...11's are difficult. I end up with a 12.01@112 with...
Top Bottom