Recent content by monster50iii

  1. monster50iii

    MDE injector nozzles anyone still running them?

    I have 60% DDP injectors and I have tune 1 setup to to feel like a stock truck. It's only 1200us or so. My injectors below 120mpa and 1000us flow about 15-25% less than the stock injectors. 120mpa and 1000us is kind of the crossover from what I've learned. The interesting part is I've had these...
  2. monster50iii

    Deleting Questions

    Most exhausts are 4in off the downpipe, and after 3 or 4ft go up to 5in
  3. monster50iii

    WWYD? Turbo time

    Hey, an s300 will survive high shaft speeds better than an s400. Smaller shaft and bearings = surface speed
  4. monster50iii

    WWYD? Turbo time

    The kit came from wcfab. I feel I could go to a 1.0 housing and not lose much drivability. Going up a slight hill at 70 and you see 6-8psi. Carries alot of boost even at super low loads. Too much sometimes as I know it robs some mpgs lol
  5. monster50iii

    WWYD? Turbo time

    Source: https://youtu.be/j9A-FVYZkQM?si=-q1K8ys8CdzE3MC_
  6. monster50iii

    WWYD? Turbo time

    Source: https://youtu.be/7QOWQaRmDNQ?si=3trqoUvzJHFD-nEl
  7. monster50iii

    WWYD? Turbo time

    . 91 housing. I just took a quick video of some drivability. Stuff and am uploading it to YouTube
  8. monster50iii

    WWYD? Turbo time

    Fwiw, I've tried 6 blade wheels on both my 64.5 turbos, and my 69 that I had. Purchased from stainless diesel. Every time I went away from the std borg wheel response and drivability greatly diminished. Some top end? Maybe? I would have needed a dyno to know as the butt dyno couldn't tell. Drive...
  9. monster50iii

    WWYD? Turbo time

    I've tried: 3794 from danville, 4094 stg2r, 64.5/73sxe, 69sxe, 64.5/68sxe, 66/73 FI. 64.5/68SXE is my favorite. Spools like stock, I can make 20psi at 1500rpms. Tows amazing, and has enough air to make the power I want. Dynoed at 655hp on a 2200us tune with the 60s I have. If you go fixed vane...
  10. monster50iii

    tips and tricks for harmonic balancer swap and water pump replacement

    So I have been looking over old threads and have a decent grasp on some of the things I'll be against for this job. What are guys using now days for install tools? I plan on getting an ATI balancer. I've put these on race engines (non diesel) in the past and we always used a dead blow hammer to...
  11. monster50iii

    Trying to locate a vibration

    Josh, u think you're correct with the balance rates jumping around causing the vibration. I narrowed it down to "something " within the tuning. I figured it was me doing something that ultimately pissed the ecm off. I made sure I'm following stock torque values for the pedal, same with fuel...
  12. monster50iii

    Trying to locate vibration

    I'm trying to nail down a vibration.. happens between 1550-1650 rpms at a light load. Flat road, it won't do it, but a slight hill it'll shake. I thought maybe ut was tune related, and for the life of me can't get it to go away. When it happens my logs show mm3 bouncing from 20-35mm3. I can't...
  13. monster50iii

    Trying to locate a vibration

    I crawled under the truck and everything is tight. My trans mount moves quite a but, so I'm replacing it. I did notice during the shake, balance rates do jump around, but from say +2mm3 to -1mm3. Not a ton of movement but maybe it doesn't take much. Trying an old known good tune file, and will...
  14. monster50iii

    Trying to locate a vibration

    I've honed in on a new vibration. The signs are making me question the trans. Here are the details: -built trans with alot of miles. Around 170k on build, 270k overall on hard parts -i make around 670hp at the tires and the trans holds it just fine, tho I rarely use even 500hp.. -the vibration...
  15. monster50iii

    Does an Lml rear seat fit into an LMM?

    My dog destroyed my rear seat. I'm curious if a rear seat from a 2011 would bolt into my 2008??
See more
Top Bottom