Another batch of Billet Manifolds

[joe@HSPDIESEL]

We finished up another batch of Billet Manifolds this morning to head over to ceramic coating. We'll have these ready to go next week!

Several sets of 2-1/4" are getting machined now as well!

989-476-0135
[email protected]

 

[snowman]

Those are beautiful!! How much do those cost? And the 2 1/4??

 

[joe@HSPDIESEL]

Those are beautiful!! How much do those cost? And the 2 1/4??

These run right around $1,650 shipped and the 2-1/4 are $2,000 with matching up-pipes. We're seeing good gains with the 2-1/4" on the higher horsepower builds so far.

 

[Evan@InglewoodTrans]

You should do some testing on the 2 1/4 in MA to make sure the results out this way match yours. You can send them whenever you like.

 

[DaveB]

You should do some testing on the 2 1/4 in MA to make sure the results out this way match yours. You can send them whenever you like.

I'll bring them to North Carolina! :woott:

 

[Evan@InglewoodTrans]

I'll bring them to North Carolina! :woott:

:hug:

 

[delong_1]

how about some high altitude testing :joker:

 

[Evan@InglewoodTrans]

how about some high altitude testing :joker:

I wish Dave was really bringing me some.

 

[sickdiesel]

You should do some testing on the 2 1/4 in MA to make sure the results out this way match yours. You can send them whenever you like.

lol ya, should do some "testing" out here in Idaho just to make sure they

 

[matt78]

Any dyno numbers with these? Lets say a truck with twins, good fuel, before and after? I would be a test subject! They look sweet.

 

[Cknight199]

I'm thinking that they should be tested in a place with a super crappy DA... Like Utah... Heck I'll volunteer and test a set for you, I'll even pay shipping!

 

[PACougar]

You guys are pathetic hiding behind testing. Joe you can just send me a free set, I don't need to test anything

 

[Hot COCOAL]

So much sickness:thumb:

Joe- I do have one request...
Would you please place a manifold gasket over your manifold and take a pic of how well the manifolds match the gasket? Please

I thought I remembered you saying that they are gasket matched, but I just thought a pic would be cool

Looks great tho, and....I saw an add in Diesel Power magazine for them too keep up the good work:happy2:

 

[S Phinney]

They are gasket matched certainly.

Sent from my XT1080 using Tapatalk

 

[DIESELMAFIAPER.LB7]

I'm thinking that they should be tested in a place with a super crappy DA... Like Utah... Heck I'll volunteer and test a set for you, I'll even pay shipping!

you and being stuck on the da of slc make me lol

 

[Cknight199]

you and being stuck on the da of slc make me lol

It sucks I went from 13.2 to a 12.7 because the air was actually good quality

 

[joe@HSPDIESEL]

Any dyno numbers with these? Lets say a truck with twins, good fuel, before and after? I would be a test subject! They look sweet.

Here are a few graphs from last fall. We're doing more with the engine dyno now. http://www.duramaxdiesels.com/forum/showpost.php?p=792959&postcount=50

 

[DIESELMAFIAPER.LB7]

It sucks I went from 13.2 to a 12.7 because the air was actually good quality

I doubt it I went from da in slc same races you were at ran same times 12.20-12.50 depending on my class I was in or 60 at 112.84 went to billings next week end ran 12.15 at......112.84 et was better due better track grab mph means my power changed 0.... Message me your mphs I don't wanna clog the sweet thread anymore

 

[matt78]

Here are a few graphs from last fall. We're doing more with the engine dyno now. http://www.duramaxdiesels.com/forum/showpost.php?p=792959&postcount=50

Thankyou

 

[bcdeutsch731]

I'm going to be running these on my new built with HSPDiesel triple turbo kit.