Search results

Search the forum Search Articles
  1. DylOrr

    LLY $0101 after erasing

    I’m pretty sure I know the answer to this question already but I figured I’d ask. 2 different LLYs in one day both took the license and erased on the full flash and after erasing went $0101 and wouldn’t recover. There’s no serial or vin in them anymore and I can’t change the vin, mode not...
  2. DylOrr

    LB7 Build

    I would avoid non complete welds as well if possible. I was originally going to drop this through the floor but doing the x in between the frame rails over the transmission is nearly impossible with a factory floor board unless you have a small transmission :D, and being able to get good clean...
  3. DylOrr

    LB7 Build

    Real race trucks dont have coolant, but I couldnt talk him out of that one just yet :roflmao:
  4. DylOrr

    LB7 Build

    I would think a 10 point would be pretty easy to do. Going through the dash would be a little difficult but nothing too hard. I know in just the x bars that go through the back of the main hoop I have about 10 hours. I’m probably 40-45 hours into this thing. I’m hoping to get a little more done...
  5. DylOrr

    LB7 Build

    I think this is gonna be the only cage I do :roflmao: I believe that’s part of the reason they asked him. Most of them are cummins and I think they want some more v8 trucks.
  6. DylOrr

    LB7 Build

    Yep tech guy cut that idea short, even though I have seen some like that. Luckily it was pretty easy. I use a finger amp control so it makes it a little easier as well. It’s not a scratch start though I do see a lot of people like that kind of welder for tight work. Like I said I’m so big I’m...
  7. DylOrr

    LB7 Build

    I figured I'd make a post about a truck we are building for a buddy of mine. He is on here, his name is Matt (Average_Ass_Lb7). It's gonna be a little long winded but hopefully we can get some good information in here as going into this whole thing I could never find much information on...
  8. DylOrr

    Strange noise at idle in gear

    It didn’t look like it at a quick glance. The belt is “wagging” and making a vibration noise. I can just set my finger on it and it stops. We haven’t looked too closely at it.
  9. DylOrr

    Strange noise at idle in gear

    My brothers lml has a similar noise. Could have swore it was a heat shield, but it is the belt. It only happens at idle in drive. New belt and tensioner and it still does it. It’s just loud enough to be crazy annoying.
  10. DylOrr

    LBZ: Perfect turbo for 100% injectors LBZ

    I've heard a ton of complaints on the 92 turbine having awful spooling characteristics. I would assume that's where a lot of the responsiveness was lost.
  11. DylOrr

    Lower oil pan for twins

    For my remote I put it in the upper pan in the front but I had my engine out. There is tons of trucks out there with lower pan drains. My brothers truck atmo charger drains in the middle of the lower banana pan and it’s never given any issues.
  12. DylOrr

    LB7: Hard/Rough Starts Cold

    Take the IC tube off and look. It should get red hot I believe.
  13. DylOrr

    LB7: Hard/Rough Starts Cold

    Just LLYs don't have them factory, LBZ+ absolutely do, but from experience I've noticed LB7s don't cold start well, and the more tired the engine the worse it is.
  14. DylOrr

    Another LLY...Another Headgasket or Maybe?.. VIDEOS

    99% of the time pushing coolant is head gaskets. But losing heat when going to idle is another tell tale.
  15. DylOrr

    Another LLY...Another Headgasket or Maybe?.. VIDEOS

    100% blown head gasket
  16. DylOrr

    03' GMC SoCal stroker

    I dig that fuel feed y. Who makes it?
  17. DylOrr

    Allison 5sp: Full Transgo?

    You said G3 for now, are the G4’s looking more promising than the G3 and worth waiting for? Also if you don’t mind me asking, what’s the benefit of drilling the c1
  18. DylOrr

    Aftermarket Flexible Engine Dipstick

    That’s a pretty good idea I’ve never thought of. Probably be pretty easy to get it right while it’s out. I bought a truck that fleece built that had a flexible one in it but unfortunately it got broke taking it apart. I might have to give them a call and see if they have something
  19. DylOrr

    Aftermarket Flexible Engine Dipstick

    I was wondering if anybody knows of an alternative for a dipstick tube for these trucks. I built a motor with the 12651877 block and with merchant mounts the dipstick wouldn’t go between webbing and the mount. I bent it differently last time but it was right on the starter and I had to wrap it...
  20. DylOrr

    Trans go converter valve- modifying for no knockdown

    I’ll just put a 6 speed set up in it then. Thanks for the quick help guys :thumb:
Top Bottom