Recent content by LBZ_Baker98

  1. L

    LLY new TCM won't communicate after TCM replacement

    Yes, i can communicate with everything when the original TCM is installed, when the new "blank" TCM from GM is installed I cant communicate with ECM or TCM.
  2. L

    LLY new TCM won't communicate after TCM replacement

    We had a LLY come in the shop with a intermittent issue, went through diag and came to conclusion TCM needed to be replaced. Got replacement from dealer took it to be programmed and they said it wont communicate, they warrantied it out got another same thing. When new TCM is plugged in they cant...
  3. L

    LML converter wont spin after tightening bell housing

    I’m a big fan of goerend unfortunately I think that’s the converter they send with all of their 725HP builds and require that converter for warranty.
  4. L

    LML converter wont spin after tightening bell housing

    No spacer behind fly wheel. Found that the stock converter seats much further then the Randy’s converter. I tried and tried to get the converter seated. After speaking with Randy’s we thing something happened in the machining process with the snout of the converter. The lugs where the converter...
  5. L

    LML converter wont spin after tightening bell housing

    The white marks on the flex plate are not scratches. It’s from where I cleaned off the paint marker I used to mark the flex plate bolts as I torqued them.
  6. L

    LML converter wont spin after tightening bell housing

    Have a randys transmission that I am installing in a 15 LML for a customer, First i was sent a LBZ/LMM flex plate so I called and they sent out the correct one, now when I bolt the transmission up the converter will not spin. I have installed countless of these allisons and never had this issue...
  7. L

    LMM P0878

    Internal harness is new, I will change the pressure switch manifold! Thank you very much for your time Mike!
  8. L

    LMM P0878

    Seems to do it all the time for the most part! regardless of hot or cold. It only does it every 30-40 or so times you go to reverse from drive or neutral or park!
  9. L

    Mangled glow plug removal

    I could be wrong but it seems like I remember my snap on guy promoting a special tool specifically built for broken duramax glow plugs a few months ago. I could be wrong and if I am not wrong I am not sure how it works or if it works but it might be something worth looking in to!
  10. L

    LMM P0878

    Have a buddys LMM that he just bought. Had all kinds of codes being thrown and truck wouldn't move, replaced the TCM and had a it programmed and truck runs and drives now but every few times you put it into reverse it throws a P0878 code and says "range shit inhibited shift to neutral to reset"...
  11. L

    Is my allison spent?

    Mike is the man with answers but you might check the round plug on the back of the trans and see if there is fluid in it!
  12. L

    LMM no start after head gaskets

    Okay, I got it figured out. I'm almost to embarrassed to say what it was but let's just say 1 loose fuel line will cause it not to build rail (obviously) lol. Like I said must have just been tired and frustrated or I am an idiot. None the less, thank you for the advice and all your time! Much...
  13. L

    LMM no start after head gaskets

    Primer bulb gets hard after about 4 or 5 pumps. Goes soft after cranking. I ran a line straight to metal line that goes to cp3 from a can of fresh diesel and truck still wouldn't start.
  14. L

    LMM no start after head gaskets

    Have a LMM we just finished head gaskets on. I don't know if I am just tired and over looking something or what. Truck will crank but won't start. only codes are IAT and Coolant temp sensor. Truck shows 5700ish psi of desired rail while cranking and only 71psi actual. Actual PSI does not...
  15. L

    Built Allison 1-2 shift flare when cold

    Okay, just to update everyone! I took the truck to Josh last Tuesday and picked it up today. He Was slammed and still managed to get me worked in. For starters my warranty was 110% expired. I failed to get the truck to him before the warranty was up despite him telling me to bring it back long...
See more
Top Bottom