LB7: Anyone make a high flow LB7 Y-Bridge?

[SSchmi5519]

Does anyone make a federal emissions style high flow LB7 y-bridge?

Post a pic if possible.

 

[TrentNell]

Does anyone make a federal emissions style high flow LB7 y-bridge?

Post a pic if possible.

If this was earlier today I shipped one today with a S510/S475 kit , i can get a pic later this week but haven't taken a pic of just our bridge.

 

[SSchmi5519]

Not in a huge rush Trent, looking forward to the pics. :thumb:

You can ship it with my intake. :drool:

 

[Tony Burkhard]

We have one and it will be ready this week. Its a full three inch and flows like no other that we have tested. Here is our flow sheet.

 

[ChevyTruckGuy78]

trent is doing mine and is makin it to fit with a 3in turbo horn

 

[ripmf666]

Does anyone make a federal emissions style high flow LB7 y-bridge?

Post a pic if possible.

I offer 2 of these and can post pics and send you prices later on tonight.

 

[tractor]

Here are a couple we sell.
Darryl

 

[Chevy1925]

View attachment 18023

View attachment 18024

Here are a couple we sell.
Darryl

doesnt the federal have the second 45* angle that makes it point right at the coolant tank?

 

[Noreaster]

doesnt the federal have the second 45* angle that makes it point right at the coolant tank?

on the 02-04s they do, 01s were stubby & had the rubber 45*

 

[Chevy1925]

on the 02-04s they do, 01s were stubby & had the rubber 45*

oh thats right, duh lol. thank you!

 

[SSchmi5519]

doesnt the federal have the second 45* angle that makes it point right at the coolant tank?

Thats the one I need. I have the curved bridge.

 

[SDP]

Thats the one I need. I have the curved bridge.

Unless you have a 3" intercooler pipe designed to go with it.

 

[SSchmi5519]

Unless you have a 3" intercooler pipe designed to go with it.

The OEM passenger side LB7 tube is 3".


Sent from my iPhone.

 

[DIESELMAFIAPER.LB7]

im interested in something like this to something that would flow more and fit with my s364

 

[DIESELMAFIAPER.LB7]

Tony when you going to have a pic of yours

 

[Tony Burkhard]

Tony when you going to have a pic of yours

I hope to have a picture up tomorrow.

 

[SDP]

The OEM passenger side LB7 tube is 3".


Sent from my iPhone.

Correct. But it does neck down to 2.5" for the 2.5" ID silicone boot, and it would not work with the pictured 3" y-bridges posted above. I was stating that you would want an intercooler pipe made to fit that style y-bridge horn instead of something similar to the factory piece which has the non standard degree bend in it:thumb: If you're doing something custom you may as well go with a better design all of the way around.

 

[ripmf666]

Correct. But it does neck down to 2.5" for the 2.5" ID silicone boot, and it would not work with the pictured 3" y-bridges posted above. I was stating that you would want an intercooler pipe made to fit that style y-bridge horn instead of something similar to the factory piece which has the non standard degree bend in it:thumb: If you're doing something custom you may as well go with a better design all of the way around.

X2 Stock goes from 3" to 2.5" makes it nice to replace with the first bridge in post 7 and have a full 3" intercooler pipe. We could have something ready for you just have to let one of us know. :hug:

 

[SDP]

im interested in something like this to something that would flow more and fit with my s364

Here is a picture of the intercooler pipe coming off of the short 3"
y-bridge, this is in a setup with an S300 similar to what you have. Not a very good picture but you get the point, Henry can get it for you.

 

[Chevy1925]

Well i have a full custom 3" boost tube for the 02-04 federal y-bridge and dont really wanna spend the money on another new boost tube and buy y-bridge. Plus i think that big hump the 01 style tube has isnt as clean as the 02-04 style IMOP.

whats so bad about the 02-04 design?