Search results

Search the forum Search Articles
  1. melms23

    LML Starter grind

    Our '11 LML has ground the starter every so often and is getting more frequent. Going to replace the starter and flywheel. Can I use one from an LBZ? I have the flywheel left over from another project. The truck is all stock and has 115k on it.
    • melms23
    • Thread
    • Replies: 2
    • Forum: LML
  2. melms23

    Dual Cp3 rail fitting

    I have a dual cp3 kit that I have pieced together over the last couple years and it has a braided supply line, from Industrial if I remember correctly. I think it might be for an lly or lb7 because the fitting looks to be for the front of the rail, because it's too small for the rear. Is...
    • melms23
    • Thread
    • Replies: 2
    • Forum: LBZ
  3. melms23

    SBC street DD pulling

    Anyone doing any pulling with one? Is it worth $1000 more for a SFI rated clutch? I only plan on doing maybe 5 hooks a year otherwise only street and racing abuse
  4. melms23

    Lbz into 02 zf6

    I sold my lmm recently and still have a built long block. I'm having trouble selling it, so I've been thinking about using it. Found an 02 zf6 with no engine. Using a harness from Ben would like to use my lbz block, heads, vvt, ect. I realize wiring and cooling stack will be an issue. My...
  5. melms23

    Merchant push rods

    Are these pushrods correct? The ends are not the same size as the stock ones. They are the same length and said 01-10 duramax on the box, but I want to be sure they are right before I put them in.
  6. melms23

    My little side project

    I picked up a 01 regular cab 2wd frame last weekend for a side project. Originally I wanted to do a 1970 c20 with ano lbz zf6. A guy local to me has a 5 speed allison and a zf6 for sale. 900 for the zf and 500 for the allison. I'm looking to keep it simple wiring wise but is spending so...
  7. melms23

    BMF/SOTA Off-road wheels

    I finally got the wheels I have been wanting for a while. 20x9 BMF novakanes. When they arrived they were in fact the new name of SOTA Off-road. No big deal and put them on. Two weeks later I lost a center cap after replacing a rear caliper, must not have snapped it in all the way. Go to...
  8. melms23

    Inside the zf6

    I've noticed very little zf6 talk on here lately. After a few hours of plowing snow for the first time I lost the synchro for 2nd. Not wanting to hurt anything else I yanked the transmission that night. Found a pdf service manual online very easily and dug in. I have none of the...
  9. melms23

    P0089 after lift pump

    Today I shimmed my fprv and then drove to the hardware store to get fittings for my lift pump. All was good. After I got the lift pump in it max's rail pressure to 26k. Turn the pump off rail is normal and no code. Everytime I turn the pump on I get the p0089 fuel pressure regulator 1...
    • melms23
    • Thread
    • Replies: 7
    • Forum: LLY
  10. melms23

    Clutch install

    I bought a used south bend dd for my work truck from 02greysixer recently and have a couple install questions. First is a new slave and pilot bearing necessary? I know the throw out is necessary and am having a hard time finding the part number. Oreilly's couldn't get one. I would like to...
  11. melms23

    G80 not unlocking

    My lmm has 130k miles with roughly 10 hooks, lots of burnouts and general hard abuse. I hopped last weekend and broke the drivers side axle. Got a used one with 90k on it. Pulled the cover and found some shavings and 2 very small chunks about the size of a pencil led. I put 4 1/2 quarts of...
  12. melms23

    Arrival blue rclb zf6

    Since my lmm has been more play than work, I picked up this zf6 to use as a farm truck from an auction site where we bought some skid steers last year. Zf's have always interested me and being arrival blue seemed sort of rare. It's a little beat up but only has 56k miles. With some...
  13. melms23

    2007 Chevrolet 2500hd

    melms23 submitted a new Showcase Item: 2007 Chevrolet 2500hd Read more about this showcase item here...
  14. melms23

    lbz block in lmm

    I have a lbz with a cracked piston for a donor motor to start building in my spare time. I plan on covering all the bases with carrillos, mahle or fingers pistons, studs, keying. Should I use lbz or lmm injectors? thinking 60 or 80 overs Af cam, billet flexplate, and dampner necessary...
  15. melms23

    cp3 pulley only

    Where can I get a dual cp3 pulley seperate from a whole kit? Looking for something plain and black. Called and emailed ppe with no response. The only one I can find is h&s and not a huge fan of it.
    • melms23
    • Thread
    • Replies: 2
    • Forum: LMM
Top Bottom