Search results

Search the forum Search Articles
  1. Harbin_22

    Mobil M1-303A Filter Differences

    I'll figure out how to post pics, but I have used the Mobil M1-303 oil filters on my truck forever. I know they changed to the M1-303A extended performance a while back. Well I picked a few more since I was using up my last one and they are different from the M1-303A I already have. The...
  2. Harbin_22

    LMM Mega Fuse Wiring Layout

    Could some point me in the right direction, or look over their mega fuse panel on an LMM and tell me what wires are where. I changed mine around years ago to make room and really wondering if I have it setup any way at all like it is supposed to be lol.
  3. Harbin_22

    LB7 $0544 when attempting to activate license

    Got a 2002 lb7 here. I can read the tune out just fine. VIN number is good, no crazy characters or anything. When trying to activate the new Vin license so I can flash it, I get the $0544 invalid serial number code. The serial number comes up as 0000000000. Anybody deal with this before? Is...
  4. Harbin_22

    LB7: P0727 help

    Swapped a trans that was slipping in 5th gear. New trans is built with Suncoast converter. Getting the P0727 immediately at start up. Tried new sensors, tried swapping TCM, checked all the wiring, no shorts no open. What's weird is everything on a scanner looks great. Turbine speed is...
  5. Harbin_22

    Little Drive Line Angle Help Please

    Need a little help figuring out of my angles are right or not. I've been chasing an odd vibration and wondering if the angles are causing it. Truck has 3" lowering shackles, overloads removed, and Tbars let all the way down. Hope I can explain this well enough... Okay, at ride height on...
  6. Harbin_22

    What Chassis Uses a 69" driveshaft

    Picked up a 6" ADM driveshaft that was supposed to be for my ccsb LMM. Well it's too short. My factory shaft is around 71" and this shaft is 69" give or take 1/4". Anyone know what Chassis configuration takes this length shaft? Probably going to sell it instead of messing with getting money...
  7. Harbin_22

    LMM Ujoint Help, 1480-1485 questions.

    I found a good deal on a 6" ADM driveshaft that has 1480 series Ujoints. As far as I can tell, my truck has 1485 joints. I've read about thinner snap rings on the slip yoke, but what about the rear yoke? Should I get new yokes on both ends to make this a legit swap?
  8. Harbin_22

    Yukon 30 spline axles any good?

    Anyone have any experience with the Yukon 30 spline 4340 Chromoly axles? Kind of figure while I'm doing gears and a TruTrac, might upgrade axles. Really don't want SCS since they are puck style, don't think my center caps will go back on.
  9. Harbin_22

    Snap On Solus Pro No Comm with TCM

    Anyone ever have a Solus Pro only not talk to the TCM? It will talk to every other module on my truck and an LBZ I was working on, except the TCM. The TCM requires K-17 key and so does the ECM. Didn't know of these keys go bad or what. It is on Version 12.2 also.
  10. Harbin_22

    3.42 Gears and TruTrac

    Looking for a set of 3.42 gears for front and rear and a TruTrac for the rear. See if anyone has a set before I buy new. Let me know. Thanks ON EDIT: This turned into a tech discussion, and since Kyle probably already bought his gears and TT, the thread was moved into the Drivetrain section.
  11. Harbin_22

    VIN Check Please looking VCI info

    Can anyone run a vin check for me? Trying to find if the dealer actually put the info in the system for MY BCM VCI flash number after they installed heated seats. Would greatly appreciate it 1GC4KXB63AF108939
  12. Harbin_22

    LMM: Finally got in the 10's

    Well I finally made it in the 10's! Went on a 10hr drive out to Maryland International Raceway to play around in the XDP even this weekend. Never ran anything other than 1/8 passes and playing under 100mph on the street. Well first pass down the track got me a [email protected]. Had a 1.7ish...
  13. Harbin_22

    Danville Custom Slotted Rotors Came In

    Got talking to Mark@Danville about new brakes for my truck, well to my surprise, they actually have some custom slotted rotors, that they machine in house, that Mark has had great luck with. Well mine showed up today, along with some ACDelco pads, and look awesome. Waiting on my braided brake...
  14. Harbin_22

    Tripples got tuned at Danville today!

    Well left the old truck with Mark for the week. He got it on the rollers today and got up to 1,100hp and 1,700+ftlbs torque out of it before the tires wouldn't hold anymore. Super happy with it! Can't wait to get it to the track and see what she does. Can't think Mark at Danville enough for...
  15. Harbin_22

    Great service as usual!

    Got with Levi Monday about some blankets for the new 369's. Ordered them up and here they are a day and half later! Awesome service and product Levi!
  16. Harbin_22

    Dropped The Truck Off at HSP Yesterday!

    Made the trip up to HSP Diesel yesterday with the black truck. Twins are out and Tripples are going on! I'll get more specific with the kit once it's all finished up, don't like talking something up that isn't complete yet(Dave@HSP might piss me off too :hug: ). For now, the turbos will...
  17. Harbin_22

    Stupid newby AFE 5" exhasut exit question

    Sorry for the newby Duramax forum type question, but I am probably moving up to 5" exhaust. Had my eye on AFE but want to see how it exits out the back. I don't like the full 90° look that points perpendicular to the truck body, some of the others point too much straight back out of the bumper...
  18. Harbin_22

    LMM: TPMS Value change with Snap On Solus Pro

    I looked around and don't find much of any info on the subject, but for anyone that needs to change the TPMS pressure setting for different tires(in my case nitto 420's), a Solus Pro has the ability to do it. They seem more common than Tech2's around regular shops. I know the dealer will do it...
  19. Harbin_22

    Needs some prayers for Matt Woertz (MaddMatt)

    Alot of you all know Matt Woertz with Blackout Diesel in Corydon Indiana also known as MaddMatt on this forum. He is a good buddy of mine and many on here. He was in a very serious accident this morning. Heard a few different reports, but the person that hit him has passed away and Matt is in...
  20. Harbin_22

    LMM: Heated Steering Wheel Upgrade

    Most of you know that I am very performance oriented, but my truck does get driven quite a bit and I like to have it as nice as possible. It started life as an LT with all you could get in an LT. Well I added the factory back up camera, Nav unit, heated cloth seats, full center console, and a...
Top Bottom