Search results

Search the forum Search Articles
  1. DetailsUnlimited

    2017 GMC front bumper and rear bumpers on a 2006 Sierra.

    Who has done this and do you have any pictures? What did you have to do to the brackets? This is what I would like to do in this pic. Thx
  2. DetailsUnlimited

    Need good lbz or lml upper oil pan an front cover.

    Need good front cover and upper oil pan. Some of the holes have stripped threads so please make sure yours are good. Thx
  3. DetailsUnlimited

    serach and advance search buttons not working.

    serch buttons not working
  4. DetailsUnlimited

    Lbz to LML just using block question

    my Lml block needs a oil sensor. The lbz one will not work. Will a lml sensor work with my wiring harness or what do i need to make this work?
  5. DetailsUnlimited

    LBZ: Looking for a replacement vavle cover bolts.

    Ive found ARP has stainless steal and black. Are there any other choices?
  6. DetailsUnlimited

    Finally getting my triple kit and rebuilding the motor

    After blowing the race motor(hole in a piston) and selling the twins at the end of 2015, i've decided to rebuild and do triples. Triples will have 2-s369's and 1-s468. Going back with 100 overs, dual fuelers, socal 6460 cam and fingers 15.5:1 pistons with .075 reliefs. Actually want to sell the...
  7. DetailsUnlimited

    Any real world info on carrillo forged pistons

    Looking for info on these piston and not just what u have heard. DR 7021 are the racing pistons with HV3D5 ring set sold seperately.16.5:1 D7020 are the street pistons and rings set is included. 15.5:1 this ring set is supposed to last longer and last up to 1300 hp.
  8. DetailsUnlimited

    Building a shop and need ideas. 40x60 metal not pole barn

    Have a few pics ill load when i have time. Ill put the TT, truck, burb and a lift in it. Want a over hang where the door will be. 2 maybe 3 garage doors. Just looking for idea to bounce off guys that had or would change what they have.
  9. DetailsUnlimited

    Who sells the nicest oil feed/drain kit? S400

    I have a LBZ motor and looking for a complete kit that isn't half ass put together for S400 turbo. Names and if you have pics that would be nice as well. Thx
  10. DetailsUnlimited

    LBZ: Hamilton springs

    Who has Hamilton springs and have you had issues? I was told that they don't last and They have been in since 2011 and I need to replace them. Any truth to this. I'm about to tare into my motor anyway so just asking.
  11. DetailsUnlimited

    Need a cherry picker

    Looking for a reliable 2-ton picker. Any name brands to go with? Thx
  12. DetailsUnlimited

    LB7: Installed a LBZ pump in a LB7 and now will not start.

    Done this many times. And have not had this problem before. Did the install. Changed the tune for the bigger pump. All sensors were hooked back up and just cranks. Log shows actual at 26107 and desired at 5800 while cranking. Not sure what is going on there? No leaks, any suggestions?
  13. DetailsUnlimited

    Question: Looking for lbs per minute on different S472's

    The new SXE FMW S472 flows 110 lbs per minute. Looking for information like this on other chargers. Compressor side.
  14. DetailsUnlimited

    In need of a stout engine stand

    Is Napa's 1250 lbs engine stand a good one. Needing to buy one. Or any suggestions on a side motor mount.
  15. DetailsUnlimited

    New EFI update issues

    Just did the update for Sept 15th and can not open my files. Deleted both programs and reloaded 3 times and still same issue.
  16. DetailsUnlimited

    Finally needing a converter for the van. Will the 6l90 converter work?

    Just needing to know if someone knows if the 6L90 converter will fit the 4L85e and if it's better?
  17. DetailsUnlimited

    LBZ: Thinking of triple turbo setup. Ideas on turbos

    Bout to sell the twins and going to triples. I still tow and daily the truck and current set up is around 900 or so. Looking for 1000-1100 and without losing drivability. S472/87 or what turbine and housing. .90/1.0 or 1.10? And a pair of S366/71, 73 or 74. T3 or T4 open. Please chime in if you...
  18. DetailsUnlimited

    Info: Arkansas Diesel Dyno Day. $55 for 3 pulls!!!

    ********DATE FOR DYNO DAY MEET & GREET!******** August 22nd @ 9am We will have prizes for most HP and random HP number we pick. Dyno address is 2400 Linda lane Jacksonville Ar Spread the word!!!!!! $55 for Dyno If you wish to come and market your company I ask that you join in with the...
  19. DetailsUnlimited

    LBZ: What makes our trucks have rail bounce?

    Had an issue with two stuck needles in injectors #6#8. Fixed the problem. And the tunes I ran in my truck before will bounce at WOT now. Had a soft code P0103 that is in the truck now reading high MAF. What sensors would effect rail bounce besides PPE box and regulators? Both pumps are stock LBZ.
  20. DetailsUnlimited

    Need some help with diagnosing this issue.

    Race last weekend and truck was fine. Sat all week and put some new boots on. Started the truck up to drive up to Branson. Smooth idle, runs good but smoke real bad. Hazes a lil at idle. Logged the truck and all looks good. Injectors as well. Found a boost leak that I thought was it, but same...
Top Bottom