Recent content by turbospoolindmax

  1. turbospoolindmax

    LBZ vs LML

    600 hp is nothing on stock rods. guys including myself have been pushing them over 1000hp for years. Tq bends rods not hp keep it under 1300ish lb ft of torque and stock 06+ rods will last pretty much forever for 600 hp. I would do lbz rods and lb7/lly pistons and call it a day. If you plan to...
  2. turbospoolindmax

    Allison transbrake

    Well here's the tear down...c1 and c3 opened up a good bit on clearance c3 was at .117 clutches look fine but steels got some hot spots. With the amount of abuse this trans took I don't think I can really blame any of this on the transbrake looks more like normal wear and tear for the abuse it's...
  3. turbospoolindmax

    Allison transbrake

    I think it is shifting into 5th I don't data log it normally but my shift points are at 4000rpm since it is a stock motor and according to my calculations it would be at over 5000rpm at 121mph in 4th but I'm honestly not quite sure mabe I should change my shift point for the 4-5 shift to like...
  4. turbospoolindmax

    Allison transbrake

    Yeah that was prolly me!
  5. turbospoolindmax

    Allison transbrake

    I will be tearing it down shortly to see how it looks since the last 2 passes I made its starting to get lazy on shifts. Could very well be c3s but it's had prolly 70-80 6sec passes on it since it's been apart and lots of road hits also when I was testing it. My theory is since I'm only...
  6. turbospoolindmax

    Allison transbrake

    So I thought I would post on here...I don't get on here a lot not sure if I'm posting in the right thread or whatever. But I've been getting a lot of questions and interest in my transbrake. So I officially have it working after tons of trial and error. Still need to work on the bump so I can...
  7. turbospoolindmax

    Transmission vent cap

    You can pop the whole thing out and npt tap the case and screw whatever type of fitting you want in there. I have my race truck trans done that way and ran to a catch can since I had it push out some fluid on the track when I was on the convertor staging. IIRC I used 1/8 npt tap
  8. turbospoolindmax

    suncoast 5spd build specs

    ya i wasnt expecting much help but figured it couldnt hurt to ask lol
  9. turbospoolindmax

    suncoast 5spd build specs

    ok i reckon ill call suncoast in the morning i was hoping somebody had a spec sheet lying around or knew the specs...i also heard of some builders setting certain clutch packs slighty tighter than spec for wear in has any of you builders heard of this? if so is it a good idea?
  10. turbospoolindmax

    suncoast 5spd build specs

    fixing to start on this trans and i realised that i didnt get any clearance specs with it its the SUN COAST GMAX-5R-1 RAYBESTOS REBUILD KIT does this kit have certain specs or can i use the atsg manual specs or better yet what clearance do the pros recomend to set these kits at!
  11. turbospoolindmax

    Who else is going to UCC?

    I'll be there! Sent from my SM-G900T using Tapatalk
  12. turbospoolindmax

    p0742 and surges when the tc isnt locked

    yup had the day off so figured id try to knock it out today its back together and working perfect so far! appreciate the help Mike! Glad i didnt have to spend money on a converter!
  13. turbospoolindmax

    p0742 and surges when the tc isnt locked

    yup that was my dumb ass mistake just pulled it apart and sure enuf it was backwards! you the man mike thanks!
  14. turbospoolindmax

    p0742 and surges when the tc isnt locked

    thanks mike thats some good info i think that is my problem i think i put the flat spotted end in first its posta be toward the spring right? not sure what i was thinking...
  15. turbospoolindmax

    p0742 and surges when the tc isnt locked

    thanks mike thats some good info i used the bolts that suncoast sent for the converter so im confident thats not the issue! one the converter valve im pretty sure i installed it how i took it out however now im second guessing myself i put the flat spotted end in first is that correct?
See more
Top Bottom