Recent content by ToyhaulerTom

  1. ToyhaulerTom

    LBZ: New problem for Turbo

    Thanks 02greysixer, Although I don't have a live monitoring tool maybe I should invest in one. This is what I was looking for, a next step.
  2. ToyhaulerTom

    LBZ: New problem for Turbo

    I'm looking for the next step in resolving an error code P003A that just popped up with the check engine light. I have a 2006 2500HD with the LBZ and 135K miles. Still runs okay but from what I've picked up on line I may have a bad VPS or solenoid. Is there any suggestions with what direction...
  3. ToyhaulerTom

    Help: Crazy brakes pulling hard on 2006 2500hd

    Jacked it up today and checked both wheels for worn bearings. The right bearing was shot, so a new one was installed. Problem fixed. I guess the bad bearing was causing the ABS sensor to give a bad reading, as all systems seem normal, although the new hub assembly came with a sensor, so its...
  4. ToyhaulerTom

    Help: Crazy brakes pulling hard on 2006 2500hd

    I do get a small amount of ABS vibration just before the truck stops. That's what led me to think ABS.
  5. ToyhaulerTom

    Help: Crazy brakes pulling hard on 2006 2500hd

    Thanks James, I'm thinking along these lines, as I see nothing wrong with the hardware itself.
  6. ToyhaulerTom

    Help: Crazy brakes pulling hard on 2006 2500hd

    Looking for help on trouble shooting a brake pull. The truck stops fine from most any speed until slowed to about 7 m.p.h. The steering wheel then turns hard to the left, maybe a half turn. Other than this goofy deal, it stops and handles fine. I'm thinking ABS? Any suggestions?
  7. ToyhaulerTom

    Question: Replacing steering wheel and inst. Bulbs

    Does anyone have info on replacing the light bulbs in a 2006 Sierra SLT that illuminate the controls on the steering wheel, and those that back-light the fuel gauge? I just want to replace with the normal bulb. I have several burnt out.
  8. ToyhaulerTom

    Lbz water pump part number

    I just installed an AC Delco pump, P/N 12637105 in my '06 LBZ. Paid $187.
  9. ToyhaulerTom

    Removing crank bolt with engine on stand

    I made a tool that holds the ballancer. I used it while the engine was in the truck and it worked great. It has a short dowel that sticks in one of the holes drilled for ballancing, and the long arm rested against the frames cross arm. It could be extended the the same length as the wrench...
  10. ToyhaulerTom

    06 lbz loosing coolant

    If you used the color changing fluid for testing for a leak, don't believe the results. I tried it on an '06 LBZ 2 weeks ago, test showed negative for a leak, but I found a blown head gasket anyway. I hope your coolant loss is found, and simple. Good luck.
  11. ToyhaulerTom

    Help: Can't get it primed or started

    Thanks you guys for the help. Got it running and all is well. The forum has been instrumental in the success.
  12. ToyhaulerTom

    Help: Can't get it primed or started

    There is no lift pump, but I've noticed a high pressure fuel leak. I must have a fitting loose on a rail, as when I crank for 5-10 seconds I then get some fuel running down the back of the engine. I will go tackle the leak issue and try again. ps: Glad I could amuse, now I know what a lift...
  13. ToyhaulerTom

    Help: Can't get it primed or started

    Whats a lift pump?
  14. ToyhaulerTom

    Help: Can't get it primed or started

    The filter is tight and pressure builds up. When I released the bleed screw fuel sprays out.
  15. ToyhaulerTom

    Help: Can't get it primed or started

    I just turned the key on my '06 LBZ and was greeted without a start. I manually pumped the primer, cranked, and repeated this about 10 times. The pump seemed to function normally, but after a few seconds of cranking the engine over, the primer went limp. Is there a better way to prime the...
See more
Top Bottom