Recent content by Daryl LBZ
-
Interior colors and paint discussion
The latest parts I sprayed with Classic Coat don't stick very well either. Yesterday I got my order from Summit. I ordered the SEM Soap, SEM Plastic & Leather Prep, and since they don't have the Color Coat in spray cans of Very Dark Pewter, I instead decided to order the graphite color in the...- Daryl LBZ
- Post #39
- Forum: Appearance & Detailing
-
Interior colors and paint discussion
Last night I took a green scotch bright pad with AJAX and scrubbed down a couple. I then cleaned them with mineral spirits, and then 90% rubbing alcohol. Then I used a tack cloth and sprayed the adhesion promoter on. Left that set for 5 minutes and then just sprayed it with 3 coats of the...- Daryl LBZ
- Post #38
- Forum: Appearance & Detailing
-
Interior colors and paint discussion
Yea I'm not quite sure what is going on. I did some more digging last night and today, both online and looking over my parts. I didn't use any of the SEM prep products when I painted everything besides the XXX Adhesion Promoter. Looking over my parts I noticed that the plastic pieces that slide...- Daryl LBZ
- Post #34
- Forum: Appearance & Detailing
-
Interior colors and paint discussion
I know this is an old thread, but I feel like I have possibly some helpful information. I'm attempting to repaint all the headliner trim pieces, overhead console, etc. I was having a difficult time getting the paint to stick. I went back and looked at SEM's website for clarity and I noticed...- Daryl LBZ
- Post #32
- Forum: Appearance & Detailing
-
Possibly a Bad ECM?
Ok so I wanted to post an update in case someone else out there has a similar problem some day. So long story short, after being too busy to really dig into this thing really deep for a few months I've finally found the answer. Turns out it was just a loose ground wire bolt on the passenger side... -
Possibly a Bad ECM?
Ok so I did some more digging tonight and I found that I was looking at this wrong when it comes to pin K. So pin K can be three different things depending on the truck you have according to the wiring diagrams I have. Three different things also means three different wire colors. So for the... -
Possibly a Bad ECM?
That is what I'm reading as well. It just doesn't sit well with me ruling the issue to be with my ECM only whenever I'm getting a high voltage reading for generator control module as well. Unless this is normal then that would explain it obviously. -
Possibly a Bad ECM?
I will try that tomorrow. The Generator Battery Control Module is throwing me off though. I would like to know why it has a high voltage signal as well. -
Possibly a Bad ECM?
The pins I'm probing with the multimeter are in Splice Pack 205 which is located under the dash. -
Possibly a Bad ECM?
UPDATE: I decided to get my multimeter out and check all the pins in Splice Pack 205 (SP205). So with the comb pulled out of SP205 I'm getting 7.53v on pin B (ECM) and 5.95v on pin K (Generator Battery Control Module Class 2 Serial Data) which indicates a data link high condition from what I... -
Possibly a Bad ECM?
Performed the load test on both batteries (separately) last night. They both came out as being good. I'm still checking over some things yet. -
Possibly a Bad ECM?
I haven't gotten anywhere further yet. I had to do some regular maintenance to two of my other vehicles over the weekend first. I went out yesterday to load test my batteries and the one was about dead, and the other was at about 50%. So, I didn't even bother troubleshooting yet until the... -
Possibly a Bad ECM?
Awesome! I will let you know probably by Monday of next week. -
Possibly a Bad ECM?
Thank you! I contacted the seller on eBay that was mentioned in a previous post and he does not have anything that will work for an LBZ ECM. I'm going to trouble shoot some more this weekend, and I will probably end up taking you up on your offer if your don't mind. -