Lb7 s10

[Dandrcycles]

Hello everyone... I just bought a 2000 S10 extended cab, bult LB7 with 4l80e, ford 9" and 4 link rear. 2 months of paperwork and 2500 miles to pick up... But when i seen it... I HAD TO HAVE IT !!

Its headed down to danville next week for more tuning and goodies....

First time at the track did 11.77 at 125.
Weighs 4100 without driver.
Has trans brake and line lock.

I hope to make it well known at the track here next year LOL.

Here is a short video.... https://youtu.be/5sbMesoNGMs

 

[kubitza123]

Looks like fun to me

 

[TheBac]

Why does that truck look so familiar?

 

[Dozerboy]

Tom
Banks build one that looked like that didn't they.

It's a sweet truck I have always like that year of S10.

Sent from my SAMSUNG-SM-G900A using Tapatalk

 

[TheBac]

I thought Banks's truck was maroon, and it was in storage or a museum somewhere?

 

[Dandrcycles]

People keep telling me they have seen my truck on tv.... I just shrug my shoulders and say.... Ummmmm, OK.

So they may be telling the truth ? Thats some funny shit LOL

 

[MarkBroviak]

It's an awesome truck and I have always wanted to build the same thing myself! Can't wait to get my hands on it and make it fly!!! We are going to have fun this season!:thumb:

 

[SmokeShow]

Looks like the truck that was cummins powered - converter guy outta Georgia? I'm having a brainfart on the name. Then I think Wade had that chassis for sale for a while?


Regardless, it looks good and should run like a scalded dog! Owner, you say the engine is built... As in billet rods, pistons, cam, heads? What's it have for fuel? Turbo?

 

[Dandrcycles]

Looks like the truck that was cummins powered - converter guy outta Georgia? I'm having a brainfart on the name. Then I think Wade had that chassis for sale for a while?


Regardless, it looks good and should run like a scalded dog! Owner, you say the engine is built... As in billet rods, pistons, cam, heads? What's it have for fuel? Turbo?

I wish it was fully built.... It has -LBZ bloc and connecting rods
-rebuild cylinder head with ARP head stud
-SoCal billet injector holder with studs
-BD Performance driver side exhaust manifold
-BD Performance SuperMax turbo kit with water intercooler
-rebuilt and bench calibrated (+10%) fuel injector
-new Industrial Injection 200% over Dragon Flow CP3 pump
-Bully Dog damper
-DP5 switch installed but actually running with only one tune
-Snow Performance water/methanol injection
-250gph Fass fuel pump


4L80 transmission built by Suncoast Converter
-triple disc lock up converter with billet cover
-all billet shaft
-TCI manual reverse valve body with transbrake
-B&M Stealth ratchet shifter
-small front and big secondary oil cooler with 2 electrical fans (I never seen over 130f even in hot days in traffic)

Rear end Ford 9”
-Bear's axle with 31 splines
-Detroit locker
-Strange center section housing
-3.50 Richmond Gear ring and pinion
-1350 u-joint with billet pinion yoke

 

[Dandrcycles]

Engine

 

[Dandrcycles]

Truck was built in canada.... Took me 2 months of bullshit paperwork to get through customs... They even made us replace the missing EPA stickers on the valve cover LOL.

 

[unionmax481]

Ive been wanting to this for a long time. I might just have to now. Truck looks good evevn with the red. I'm not a red paint fan. But this one is sharp. When is mark tuning this I might need to stop by and check it out. Im just right down the road

 

[Dandrcycles]

I just thought it would look funny parked next to my 1000hp silverado ss LOL. I tried to get a plate that said MINIME but it was not available.... Ended up getting JUNKR LOL

 

[Dandrcycles]

Texas speed 408, ported west coast cylinder heads, vortech v7 ysi, all wheel drive... Quite fun