Recent content by DurtyMaxin

  1. D

    Hard 1-2, 3-4 shift, delay before gears grab??

    PM'd you :)
  2. D

    Hard 1-2, 3-4 shift, delay before gears grab??

    Let me know when I can order the trim springs :)
  3. D

    Hard 1-2, 3-4 shift, delay before gears grab??

    I hear great things, the guy I bought the truck from raved about him just like everyone else, a stand up guy!
  4. D

    Hard 1-2, 3-4 shift, delay before gears grab??

    Because it costs time/money I don't have to spare right now, otherwise i would. I have no problem splitting my valve body, just want to get an idea where to start, and from what I've read I'm thinking those springs might be a potential source of my problem.
  5. D

    Hard 1-2, 3-4 shift, delay before gears grab??

    Hey Mike! Previous owner says early 2013, 30k miles ago, said it was a stage 4 build with suncoast internals. I'll order a new sump filter and I will order springs from you.
  6. D

    Hard 1-2, 3-4 shift, delay before gears grab??

    Around 30k miles, Ventura, CA, Snap-on Modis, when the trans was built.
  7. D

    Hard 1-2, 3-4 shift, delay before gears grab??

    2005 LLY, Mike L built 5 speed, out of the blue hard 1-2 and 3-4 shift, progressed rapidly now 5-10 second delay before it'll shift into reverse or drive, just a few minutes ago when it tried to shift 1-2 it had 10 seconds of hang time and then SLAMMED into gear. Fluid is still good and full...
  8. D

    Air bags for 6" Deavers?

    Hey guys! So the misses and I are in the midst of deciding where we'll be going after her contract (US Navy) is up. We've settled on three choices where we'll be happy and while we decide we will be preparing. I will be towing a large enclosed trailer with my k5 blazer inside, but also lots...
  9. D

    new parts, no power steering, still have power brakes

    Thank you for the reply. I was pretty dang sure it was but been trying to find some confirmation lol. I guess I'll be buying that box! It really sucked after all that work to still not have power steering haha. By the way, I snapped a moog problem solver pitman arm after 15k soft miles...
  10. D

    new parts, no power steering, still have power brakes

    Hey guys, so I just replaced my entire power steering system, brand new pump, pulley, hydrobooster, all lines (except for low pressure return from steering box to pump), added a cooler and magnefine filter. The only thing I didn't replace is the steering box. After 4 days of bleeding and...
  11. D

    Chassis harness

    I'm looking for details on all the connections on my chassis harness. This is the big harness that follows the frame rail down towards the EBCM. I need photos, details on the removal procedures, and diagrams. Mine has some cuts and missing plugs and the loom is full of dirt and power steering...
  12. D

    LLY guys, I need some assistance with numbers!

    Hey guys, I'm looking for LLY guys' 0-60 MPH distance, as well as 0+ WOT after 500 feet. It will be for estimation purposes, as I'm not sure way my numbers are, and I can't log my own as a snapped pitman arm and bent centerlink have me out of commission for now. My truck has no tuner, has EGR...
  13. D

    Body mounts, a little help please!

    I just got done compiling a list of the correct part numbers for my 04.5 2500HD. The bottom mounts don't have the metal piece, just the cushion. My truck is missing 2 of the full lower mounts (no bolts). Is 15201791 the correct part number for the middle/front lower mounts? Does anyone have the...
  14. D

    Need a little electrical help, dash harness wire guage?

    My truck came from the dealer (used) with the 3 12 volt cigarette plugs, the ash tray lamp, and the glove box lamp all disconnected. The wire on the ash tray lamp is smaller than the wire I'm tapping into to hook it up (dimmer wire at the radio harness). I'm no electrical guru, in fact, I rarely...
  15. D

    Anyone with BDS 7" NTBD lifts?

    Yes BDS makes it and it's actually a really nice kit! There was only one catch that made it irritating but that's not BDS's fault, it was mine for not checking clearance of the jounce bumper drop bracket and torsion bar bracket on the control arm. There was rubbing between the two. I have 35"...
See more
Top Bottom