New Toy

countrycorey

Trust Me I'm an Engineer
Jan 30, 2010
1,505
33
48
LA
the pump will run for a couple seconds when you flip the key to run and then shut off. when the engine is running, the pump runs the whole time. its basically a "prime" when you key on engine off
That is what I thought. Thank you for verifying that James!

Sent from my SM-G991U using Tapatalk
 

countrycorey

Trust Me I'm an Engineer
Jan 30, 2010
1,505
33
48
LA
Update

Seems the fuel pump is dieing as it'll start and run at idle, but will not Rev past 1000 rpms without stalling.

Sent from my SM-G991U using Tapatalk
 

countrycorey

Trust Me I'm an Engineer
Jan 30, 2010
1,505
33
48
LA
Time for another update.

Got the new fuel pump installed yesterday and was able to drive it around town yesterday afternoon. Also put a new set of lug nuts on it as it was missing a few when I got it.

2 things I noticed while driving it around yesterday afternoon.
1. Seems as if it wont rev past 3000 while driving, didn't really push it though
2. Seems like every time I slow down coming to a stop sign or red-light, when I stop it stumbles and dies. I am able to start it right back up with no issue and continue on

Sent from my SM-G991U using Tapatalk
 

countrycorey

Trust Me I'm an Engineer
Jan 30, 2010
1,505
33
48
LA
View attachment 106121

use a paper clip and go to the ALDL connector (its what the obd1 scan tool would plug into). bend the paper clip into a U and use it to jump A and B together. dont worry, wont throw sparks or kill anything. it will put the computer into self diag mode and flash the check engine to match stored codes. you will get 2 stages of flashes kinda like morris code. it will do a quick blink/s then pause, then a quick blink/s again and pause. The first blink/s is the first digit of the code, second blink/s is the second digit of the code. once it does the first code, it will jump straight to the next numerically higher code and blick for the first and second digit like the first code. if will do a loop of all the codes until you pull the paper clip out. if you want to start over, pull the paper clip and put it back in, it will start at the beginning again. if it does one blink, then blinks twice, that code 12 which means no stored codes.

to clear them, pull the battery and let it sit for15-30 sec. it should clear the codes.
Time for another update. Was able to scan the codes causing the CEL to illuminate and these are the three that came up.

15 - Coolant temp sensor or circuit fault (signal voltage high)

34 - MAP sensor voltage is low during ignition on

54 - Fuel pump circuit fault or mixture control solenoid fault or ECM fault /EGR solenoid #2 fault

Going to disconnect the battery a d see what clears. Fuel pump/relay code may be due to me troubleshooting the fuel pump
Any suggestions?
5f7e7a88caaea3776945b7af15cbb7db.jpg
b667978910f4be24057a32e9ae0dd44f.jpg
93a4461fefd199e0d5685054527091c8.jpg


Sent from my SM-G991U using Tapatalk
 

Chevy1925

don't know sh!t about IFS
Staff member
Oct 21, 2009
21,065
4,734
113
Phoenix Az
lets see what comes back. coolant temp sensor and map issue may be the reason it falls on its face over 3k rpm
 

countrycorey

Trust Me I'm an Engineer
Jan 30, 2010
1,505
33
48
LA
lets see what comes back. coolant temp sensor and map issue may be the reason it falls on its face over 3k rpm
The coolant temp sensor or circuit fault (Code 15) and the MAP sensor signal voltage is low at ignition on (Code 34).

Looks like I need to order a new map sensor and Coolant sensor.
3c6586c7b2d3a070a8bac8e7a224a9f9.jpg
d8fcbff8fbae86be0cddb83f58aadbab.jpg


Sent from my SM-G991U using Tapatalk
 

Chevy1925

don't know sh!t about IFS
Staff member
Oct 21, 2009
21,065
4,734
113
Phoenix Az
verify the voltage first. see what the map sensor is seeing. it should have a dedicated 5v to the sensor, a ground and a sensor wire. see if its getting 5v. if not, start back tracing. may have corrsion build up somewhere. coolant sensor may just need replacing, they are cheap enough to jsut throw on at it and see.
 

countrycorey

Trust Me I'm an Engineer
Jan 30, 2010
1,505
33
48
LA
lets see what comes back. coolant temp sensor and map issue may be the reason it falls on its face over 3k rpm
Also found this on while.looking at the MAP sensor and the EGR. Is there supposed to be something plugged in there?
3b458c5f5814484fd7c63be8c0ed12aa.jpg


Sent from my SM-G991U using Tapatalk
 

countrycorey

Trust Me I'm an Engineer
Jan 30, 2010
1,505
33
48
LA
verify the voltage first. see what the map sensor is seeing. it should have a dedicated 5v to the sensor, a ground and a sensor wire. see if its getting 5v. if not, start back tracing. may have corrsion build up somewhere. coolant sensor may just need replacing, they are cheap enough to jsut throw on at it and see.
I'll pull the connector in the morning and see what I can find. It should have 5v with the key in run, correct?

Sent from my SM-G991U using Tapatalk
 

countrycorey

Trust Me I'm an Engineer
Jan 30, 2010
1,505
33
48
LA
First thing I found was the connectors for both sensors (Coolant and MAP) have broken retaining clips.

MAP sensor has 5V supply with the key on and >0.3V on the other two pins when connected to ground. Gonna replace both sensors and see if I can get replacement connectors for the wiring harness.

Also got the windshield wipers working!! Still can't get the rear hatch open, need a second person to help.
924760f89f86ffd6f1c03b602abfb3b7.jpg
136e50383b278ab704e633f657128bcd.jpg
b372ab8bf4cb84f262b6a10c0d14926a.jpg
a63fdb1a5080248db455df4dae7ef808.jpg


Sent from my SM-G991U using Tapatalk
 
Last edited:

countrycorey

Trust Me I'm an Engineer
Jan 30, 2010
1,505
33
48
LA
Just for shits and grins, my plans are to eventually swap out the engine and/or EFI system. Main two options I have been considering are:

1. 383 SBC with an aftermarket EFI system (Sniper or Pro-Flo)
2. LS swap (not sure what engine or EFI setup)

Main issue I am running into is the failing connectors and unknown wiring issue/repair quality.


Also would like to do either an SAS or IFS Lift, but those are off the table until the engine is running reliably or EFI swap is done.
be1dbb8480379afc1b10ab06fb6b3e6b.jpg
0c70ca5ad88694632d3dfcd404f98713.jpg
9847ff11f7f4084a212aabe3ef888aaa.jpg
b298a035fd56e42326ead423165e3d0a.jpg
30e168da015757a587425c0807bb88cc.jpg


Sent from my SM-G991U using Tapatalk
 

countrycorey

Trust Me I'm an Engineer
Jan 30, 2010
1,505
33
48
LA
Next update:

Been driving it on my Fridays and have notices once it warms up that it didn't stall this past Friday when driving it around. I ordered a new Coolant sensor and MAP sensor to replace the old ones. The coolant sensor was broken off leaving only the pins exposed, and it had the wrong connector plugged into it. Replaced the MAP sensor and connector and then disconnected the battery to reset any codes.

Started the truck and idled much better instantly and no stumbling when stabbing the throttle, and NO CEL!!!!

Also put husky liners up front and in the cargo area!


Anyone know where a spare tire mount for a two door tahoe or yukon would be laying around is?
4337f16aee40b8b9cf304e3864a1d9ea.jpg
3635bce6eae8dff2c409c214cc400c75.jpg


Sent from my SM-G991U using Tapatalk
 
Last edited:

Chevy1925

don't know sh!t about IFS
Staff member
Oct 21, 2009
21,065
4,734
113
Phoenix Az
LS swap with a carb intake and throttle body on top, then choose an efi system that will run coil on plug igniton (cant run a distributor on a LS).

otherwise id say to just put heads cam intake (absolute most you can afford) on, a throttle body efi system and go have fun. you will be limited by the NV3500 and clutch anyhow.
 

countrycorey

Trust Me I'm an Engineer
Jan 30, 2010
1,505
33
48
LA
LS swap with a carb intake and throttle body on top, then choose an efi system that will run coil on plug igniton (cant run a distributor on a LS).

otherwise id say to just put heads cam intake (absolute most you can afford) on, a throttle body efi system and go have fun. you will be limited by the NV3500 and clutch anyhow.
You need to swap in an lq4 and have some fun with that thing!
5.3 or 6.0 and maybe this? Or ive always wanted a 383
0c9e9de650e4533601f8982a4a8cacfe.jpg


Sent from my SM-G991U using Tapatalk
1c8561dc81f0624207f224a8ef26511d.jpg
 
Last edited:

countrycorey

Trust Me I'm an Engineer
Jan 30, 2010
1,505
33
48
LA
Update:

I've daily'd it for the last two weeks and other than the loud ass holey exhaust and rattle can cat, it drives pretty good. Also, I found the glove box internals with the list of RPO codes. Now to decode it a d see what I have
6b45e9a5ae6567cdde42198356b0b8e1.jpg


Sent from my SM-G991U using Tapatalk
 

darkness

Well-known member
Jul 15, 2009
1,217
304
83
47
vegas
LS swap with a carb intake and throttle body on top, then choose an efi system that will run coil on plug igniton (cant run a distributor on a LS)
LS swap with a carb intake and throttle body on top, then choose an efi system that will run coil on plug igniton (cant run a distributor on a LS).

otherwise id say to just put heads cam intake (absolute most you can afford) on, a throttle body efi system and go have fun. you will be limited by the NV3500 and clutch anyhow.
they make distributer conversions for the ls.
 
Last edited by a moderator: