Duramax Diesels Forum Truck of the Week
  #1  
Old 07-10-2019, 01:58 PM
DPC's Avatar
DPC DPC is offline
Hotrodder
 
Join Date: Jan 2012
Location: Adams, TN
Posts: 259
Default mysterious coolant system issue

Truck is a 2012 LML with an H&S tuner, head studs, and a full delete kit. Has a new surge tank and cap. Water pump and thermostats changed when studs were done.

The truck will get up to operating temp and some of the coolant will flow into the fender side of the surge tank. After the truck has been sitting overnight the coolant level will be low enough to give the low coolant message. The coolant on the fender side is still there and not siphoning over to the pressure side when cooling. This happens every day the truck is used. The fender side of the coolant tank continues to fill a little each day and never makes its way back into the pressure side.

We put a pressure tester on the system for an hour @ 20lbs and did not find a leak. I am going to put dye in the system and let him drive it for a day and check for a leak.

I am assuming a leak somewhere is causing this issue, is my understanding of how this coolant system works correct? Thanks.
__________________
2006 5.9 4X4 QCSB
Exhaust
EFI Live
2003 LB7 4x4 ECSB
Injectors/Dual CP3s
Built tranny
GT4094R
EFI LIVE

620.5 RWHP 1170TQ 12/12/09 Bean's Diesel
Reply With Quote
  #2  
Old 07-10-2019, 02:13 PM
DAVe3283's Avatar
DAVe3283 DAVe3283 is online now
Heavy & Slow



 
Join Date: Sep 2009
Location: Boise, ID, USA
Posts: 3,099

Default

If the cooling system isn't drawing a vacuum when cold (collapsing the upper radiator hose), then it is pulling in air somewhere as it cools. The theory is the only place to let fluid in/out of the system is the expansion tank, which captures excess coolant as it expands, then pulls it back in as it cools. If there is some other way for air to get in, it will pull air in from that leak instead of lifting the coolant back in, as moving the air is easier.

Since the system holds pressure in a pressure test, that implies there are no leaks, so I would be suspicious of the surge tank and cap. Just because it is new doesn't mean it isn't bad.
__________________

Reply With Quote
  #3  
Old 07-10-2019, 03:15 PM
DPC's Avatar
DPC DPC is offline
Hotrodder
 
Join Date: Jan 2012
Location: Adams, TN
Posts: 259
Default

Thanks for the info, I am going to clamp the lower surge tank hose and put a vacuum through the upper hose using my mityvac (with the cap on) and see if I can get to pull over.
__________________
2006 5.9 4X4 QCSB
Exhaust
EFI Live
2003 LB7 4x4 ECSB
Injectors/Dual CP3s
Built tranny
GT4094R
EFI LIVE

620.5 RWHP 1170TQ 12/12/09 Bean's Diesel
Reply With Quote
  #4  
Old 07-11-2019, 06:34 AM
JoshH's Avatar
JoshH JoshH is offline
Daggum farm truck
 
Join Date: Feb 2007
Location: Texas!!!
Posts: 13,129

Default

My guess is head gaskets.
__________________
06 Silverado 4x4 CC/SB

06 Express 2500 Duramax Van "The Dumpster"


Reply With Quote
  #5  
Old 07-11-2019, 08:55 AM
DPC's Avatar
DPC DPC is offline
Hotrodder
 
Join Date: Jan 2012
Location: Adams, TN
Posts: 259
Default

Thought about that also, but I want to eliminate everything else before I recommend head gaskets...
__________________
2006 5.9 4X4 QCSB
Exhaust
EFI Live
2003 LB7 4x4 ECSB
Injectors/Dual CP3s
Built tranny
GT4094R
EFI LIVE

620.5 RWHP 1170TQ 12/12/09 Bean's Diesel
Reply With Quote
  #6  
Old 07-11-2019, 09:31 AM
JoshH's Avatar
JoshH JoshH is offline
Daggum farm truck
 
Join Date: Feb 2007
Location: Texas!!!
Posts: 13,129

Default

I had an '11 doing the same thing, and it was head gaskets. That's why I said that. The guy had even put a new coolant tank and cap from GM on it before he brought it to me because that's what he thought the problem was.
__________________
06 Silverado 4x4 CC/SB

06 Express 2500 Duramax Van "The Dumpster"


Reply With Quote
  #7  
Old 07-11-2019, 10:26 AM
DPC's Avatar
DPC DPC is offline
Hotrodder
 
Join Date: Jan 2012
Location: Adams, TN
Posts: 259
Default

Would the system build enough pressure to make the radiator hose rock hard? The reason I ask is that I went out and flogged this truck to try and get it to build pressure and nothing.

After he brings the truck back and if the coolant system checks out I'll pull the heads and have them pressure checked... I've seen cracked heads before on 3 Duramax trucks and they have all been on the coolant/intake side causing similar issues, just never an LML that already has studs with only 115k. When I figure it out I'll update. Thanks for the input.
__________________
2006 5.9 4X4 QCSB
Exhaust
EFI Live
2003 LB7 4x4 ECSB
Injectors/Dual CP3s
Built tranny
GT4094R
EFI LIVE

620.5 RWHP 1170TQ 12/12/09 Bean's Diesel
Reply With Quote
  #8  
Old 07-16-2019, 06:59 AM
SheeB SheeB is offline
Gearhead
 
Join Date: Oct 2013
Location: Ottawa,Ontario,CANADA
Posts: 31
Default

Quote:
Originally Posted by JoshH View Post
I had an '11 doing the same thing, and it was head gaskets. That's why I said that. The guy had even put a new coolant tank and cap from GM on it before he brought it to me because that's what he thought the problem was.
Same thing as my '12, ended up being HG's. Used Arp's for the repair.
__________________
2012 LML CCSB Deleted w/Motor Ops tuning, 5" Flo Pro w/3" DP.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -7. The time now is 10:00 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
vB.Sponsors