Duramax Diesels Forum Truck of the Week
  #16  
Old 01-21-2019, 08:10 AM
Bdsankey's Avatar
Bdsankey Bdsankey is offline
Gearhead

 
Join Date: Feb 2018
Location: Oshkosh, WI
Posts: 601

Default

Quote:
Originally Posted by unionmax481 View Post
I've talked to few guys about this and there is a lot 1k-1200 hp trucks with 625 studs no Orings with no issues
I've heard this as well.

I'm around 1k and have the cheap ARP studs with a 0.050 gasket from SoCal and its held just fine at 70-72psi of boost out of my 475 with lots of fuel.
__________________
Current Rides:
1) Toy: 2005 LLY ECSB, Leather, Sunroof
-820hp/1748ft-lbs @ Duramax Tuner (6/25/18) - Old 475/87/1.00 setup
-Built Motor, Forced Inductions Billet ETR 480/96/1.10 T6 w/V2 Race Cover, Modded Exergy 250% Injectors, Exergy 14mm Street Pump/LBZ CP3, Goerend Q Converter, Billet Trans, Fuelab Supply Pump/Reg, RCD Sump, Front E-Locker, TrueTrac, Yukon 4340 Rear Shafts, Traction Bars, DHD Center Link Brace, DHD Lower Crossmember Support


2) DD/Tow Rig: 2002 LB7 CCSB, Leather, Loaded
-Bosch NEW Injectors, FASS 150, 3" Downpipe, 4" Downpipe Back, RCD Sump, PPE Sleeves, DHD Centerlink Brace, DHD Lower Crossmember Support, Steering Wheel Radio Control Swap
Reply With Quote
  #17  
Old 01-21-2019, 09:59 AM
unionmax481's Avatar
unionmax481 unionmax481 is offline
hot rodder
 
Join Date: Aug 2014
Location: lebanon in
Posts: 221

Default

I do have the cheaper studs in mine also right 1100 hp with Danville 68 with 488 85 psi of boost still holding good but I am going to change over to the 625
__________________
ccsb 20"fuel hostages, Danville s480 over Danville 68 stg 2r twins, exergy 12mm stroker pump, brian crower rods, 16:.5 fingers cast pistons,socal 3388 cam, MA moley push tubes, 150% over exergy squiters, and all studded

Tuned by Mark Broviak @ Danville Performance

IBEW 481
Screw it just money can't take it with you
Reply With Quote
  #18  
Old 01-21-2019, 10:59 AM
Chevy1925's Avatar
Chevy1925 Chevy1925 is offline
don't know sh!t about IFS

 
Join Date: Oct 2009
Location: Phoenix Az
Posts: 15,444

Default

going o-ring or fire ring is dependent on power level, what you plan to do with the truck and the abuse the engine will see. some guys need it at 1000hp, others get away till 1300hp.
__________________
Quote:
Originally Posted by JoshH View Post
Mike L is my role model. I want to be like him when I grow up.
James

02 LB7, LLY, LBZ, LMM, LML, L5P 2500HD CC/LB dmax/alli "The Limo"

BIG THANKS TO: Mike L, Steve, Trent, Guy, Dan, Ruben, Josh H, Scott, Brian and everyone else who has put a hand in to help me.

best time to date: 12.39

motor died/bent rods = 3/11/11
back from the dead 7:04pm 4/9/2012

Limo is back in the garage, now driving a built chevy tracker
Tailgate Crew Member #4
Reply With Quote
  #19  
Old 01-21-2019, 03:07 PM
Chilly Chilly is offline
FNG
 
Join Date: Dec 2018
Posts: 22
Default

Quote:
Originally Posted by Chilly View Post
I am running around 900HP and 80lbs of boost.
Wagler sent me some O-Rings that are 0.070' thick and was told to cut 0.063', only leaving 0.007" of protrusion. Does this sound correct? What size wire is everyone running and how deep are you cutting?
I am just looking to O-Ring the head...

Thanks,
Anyone???
Reply With Quote
  #20  
Old 01-21-2019, 03:59 PM
Ne-max's Avatar
Ne-max Ne-max is offline
I like turtles
 
Join Date: Nov 2011
Location: omaha ne
Posts: 3,046

Default

Quote:
Originally Posted by Chilly View Post
Anyone???
Listen to wagler. Why are you second guessing them?
__________________
2013 ccsb Tow rig
2006 rclb 6.6
The fun stuff. Built motor, trans, triples, nitrous
Reply With Quote
  #21  
Old 01-21-2019, 08:50 PM
Chilly Chilly is offline
FNG
 
Join Date: Dec 2018
Posts: 22
Default

Guys, I am just comparing o-ring sizes..
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -7. The time now is 04:40 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
vB.Sponsors