Search results

Search the forum Search Articles
  1. wilsondiesel

    Transmission issues?

    Has anyone seen transmission issues out of these? I have a customer that has a 2016, is having issues of no reverse engagement when parked on a hill. Fluid level and pressures are good. No codes. Truck is deleted are the only mods
  2. wilsondiesel

    Filled Block w/ Stock Heads?

    Has anyone ran a dry/filled block along with running factory aluminum casting heads? It would be in a pulling engine so would not have much run time except a few minutes going down the track.
  3. wilsondiesel

    Which forged piston??

    I’m building a lb7 sled pull engine this winter with a partial filled block and I’m having a hard time deciding between Mahle Forged, Fingers Mahle Forged, Ross pistons or CP. is Aries owned by CP now? Or are there any other brands I should look into? Diamond is a little rich for my blood. From...
  4. wilsondiesel

    Injector Cleaner/Top End Cleaner

    Went to buy some GM injector cleaner to run through a truck, AC Delco #x66P 88861803, but they said it was discontinued and here’s the new part #19355198 which just says it’s Top Engine Cleaner. Has anyone just used the top engine cleaner to run through and had the same good results as it’s...
  5. wilsondiesel

    Edge Pulsar

    Anyone else on here running the Edge Pulsar module on their L5P? I have a beta test unit on mine. It really surprised me on how it woke the truck up even more! Going to do some more testing to see how it does on fuel mileage while towing.
  6. wilsondiesel

    Frame stretching

    Currently run an ecsb truck and would like to make it a eclb truck to gain wheelbase, how many of you all have lengthened the frames and not had issues? I know of a lot of Dodge guys that have done this, but don’t see many Chevy guys do it. At the same time we would box the frame along with draw...
  7. wilsondiesel

    ZF6 Pullers out there?

    I have a buddy with a ZF6 LLY, south bend dual comp clutch, 68mm charger, 10mm pump and 45% over injectors. He is running to aggressive of mud tire, and is having a hard time coming out of the hole smooth. Any advice on to switch to all terrains that he can blow off out of the hole? Or what gear...
  8. wilsondiesel

    Diesel Cruze

    My girlfriend is looking into getting a new to her car in the next couple of months, so I talked her into looking into a diesel Cruze. Any years we need to stay away from or things need to specifically look for when buying one? Thanks!
  9. wilsondiesel

    2.6 Smooth Bore

    Well our “workstock/2.5” got bumped up to 2.6 smooth bore class. I have heard that it’s hard to be competitive for cheap with a Duramax with this class compared to a Cummins. What is you current 2.6 guys advice? We are only running 100% overs, single 10mm pump, stock bottom end. Plan to run dual...
  10. wilsondiesel

    Pesky P0872

    Have an LLY just got done building the trans on. Had issues out of the original valve body with what believed to be a sticking e shift valve. So swapped a known good one out of my daily driver lb7 into the LLY to varify it was a vb issue Decided to go with a brand new vb that I had found on eBay...
  11. wilsondiesel

    Lmm/lml Cab and Chasis delete

    What is everyone using for exhaust kits/delete pipes on lmm and lml cab and chassis trucks? Have a guy wants me to put 5” on his lml c&c but doesn’t look like theirs enough room at the most rear fuel tank/frame rail
  12. wilsondiesel

    Trxus STS vs BFG K02

    Who all has used both and what do you prefer on a single rear wheel puller? I have used 285/75/16 BFG K02’s for the last two seasons and have had great luck with them on my workstock puller. Been thinking about trying the Trxus STS this next year if enough guys thought they’re worth it. Will be...
  13. wilsondiesel

    Mini Spool w/ Duals

    Who all has ran a mini spool in the rear with stock axles and duals before? Looking at building a new setup this winter and thinking about trying a mini spool.
  14. wilsondiesel

    Cummins Shop Manual?

    I'm overhauling a 2005 5.9 CR Cummins, does anyone know where I can find a shop manual that would have all the torque specs along with measurements? I have googled some but only really found things for earlier 12v 5.9, does anyone know if they're mainly the same older vs newer 5.9 on specs...
  15. wilsondiesel

    VP Diesel Race Fuel?

    Anybody run the VP Diesel Race Fuel in their Duramax? I've got a buddy that has ran it in his Cummins 3.0 pull truck and picked up 30hp on the engine dyno just by switching to the fuel. Curious to what other guys are running instead of just pump #2.
  16. wilsondiesel

    Biggest Dually Tire Size?

    Whats the biggest dually tire size I can run on my 2001 dually before needing spacers? Its got 235/80/16 on it now.
  17. wilsondiesel

    GM head gaskets or Victor Reinz?

    Who prefers which brand and why? I've used a few sets of VR head gaskets but recently got a top end kit that has the GM copper colored ones in them. Is that copper color actually like the copper coat spray or just the color of material?
  18. wilsondiesel

    C0308 Code wtf??

    So just put a motor in this truck, only code I have is C0308 and it kicked it into 4low. Can't get the truck to or even the encoder motor on tcase to try and switch to 2wd. 4low light is lit up but when push 2wd light it doesn't light up or anything. Also get a service 4wd message all the time...
  19. wilsondiesel

    To AF or not?

    So I have the motor out, head studding it along with porting heads, valve springs, and push rods. Running an ihi with s366 center section in it for Air. I plan to pull the motor again next year and do rods and more fuel. Currently still going to run stock fuel this year. Would I see any benefits...
  20. wilsondiesel

    Conpeco Oil?

    Anybody ever hear of or run Conpeco oil? They make engine oils, gear oils and fuel additive. Supposably is used in a lot of big sled pull tractors and ag industry. Their 15w40 is supposed to have a lot higher zinc content along with some other contents not found in others. I ran into the guy at...
Top Bottom