Search results

Search the forum Search Articles
  1. B

    Lower radiator hose heater Experiences?

    It's that time of year here in central Pa. Every year at this time I realize that I hate how long it takes my cruze diesel to get up to temperature in the mornings to defrost the windshield and blow heat. My car is equipped with the factory oil pan heater option. I admit I don't use it as...
  2. B

    LML pcv pil drain tube delete??

    While in the process of building a motor for my lml and trying to clean things up a bit to make it look like a built motor under the hood. I have decided to get a set of billet valve covers to go with all my powder coated parts. The questions is does anyone know of anybody making a small...
  3. B

    Prayers for all the family friends, members and workers in Florida

    First off sorry if this is posted in the wrong section. Just thought while I'm sitting in my hotel near Concord N.C. getting ready to head into Florida within the next day or so. That I just want to ask for everyone to keep all the families, members or workers heading into Florida in their...
  4. B

    Advice needed.

    Well my 2013 3500hd all stock broke the crank shaft @115k. Spun main bearing #4 in the process so it's junk. My options to fix it are buying a used short block, throwing in new bearings, using my top end and adding head studs, a cp3 swap and y bridge, exhaust and a single heavy tow tune...
  5. B

    Crank replacement?

    Just wondering if anybody has had any luck just replacing the broken crank with a new one without completely tearing down the whole engine and having the rotating assembly spin balanced? My lml broke a crank shaft last Saturday night. Truck is all stock except for lift, tires and steering...
  6. B

    Duramax fuel line replacement

    I'm looking to replace all my restrictive factory hard fuel lines with 5/8 an line. I know I've seen a few treads on this before and I have some good screen shots I took. But up at the engine I want to put a junction block to run my feed lines into then out to the cp3's. Also want to run a...
  7. B

    2017 L5P Alaskan Edition

    I just figured I'd start a tread on this since I never heard of one of these trucks. Today went past my local dealer and sitting right out front is a blue 2017 l5p and right on the side of the bed it said Alaskan. Has anyone seen these. From what I seen doing a search they're supposed to come...
  8. B

    Chevrolet cruze diesel

    Not sure what thread to post this. Please move if needed. To start vw is buying back my jetta tdi. So I'm looking to purchase a 2014 chevrolet cruze diesel with 10,190 on the odometer. But I've read some bad reviews of a lot of people having emission problems and regen issues. The guys on here...
  9. B

    Switch on the fly LML tuning.

    Just curious if anyone is running oe of Duramaxtuners new LSP-LML switch on the fly switches. I seen on their FB that they've released them mid Dec. They look just like a dsp5 switch, install also looks about the same. Their tuning is $300 more for switch on the fly tunes and the switch is $40...
  10. B

    Anyone running falken wildpeak at3w?

    Anyone running a set of falken wildpeak at3w? I'm considering putting a set of these in a 315/70-17 on my lml dually. The price for these tires seems to be pretty decent if they're okay tires.
  11. B

    Real wheels question?

    Hopefully someone can help me out. I'm looking to buy a set of real wheels for the front of my puller. Looking for either 10 or 12 wide. The truck is a dually. I'd like to remove the front wheel adapter and just bolt on the wheels. What off set do I need to buy? Any one have pictures of a...
  12. B

    WTB lmm dual cp3 kit.

    I'm looking for a dual cp3 kit for my lmm. Looking for a kit where the cp3 replaces the Ac compressor. Let me know if anyone has anything new or used. Thanks a lot Chris
  13. B

    Wtb real wheels.

    I'm looking for a set of real wheel for the front of my pulling truck. Truck is a 3500 dually. I want to remove the cast spacers and get the proper offset in real wheels so I can shed a few pounds and hang more out front. Does anyone know what off set I would need so the stick out a little...
  14. B

    Reciever hitch pictures.

    I'm about to build a hitch set up for my lb lmm to tuck my hooking point in as close to the back of my truck as possible. I'm removing my bumper and adding a roll pan. Was gonna use a piece of 4x4x1/4" square tubing and cut a square hole in the middle for the reciever tube to slid through and...
  15. B

    WTB Lbz injectors.

    Wanted to buy low milage LBZ injectors with good balance rates that I could send into exergy.
  16. B

    LBZ: WTB exergy 100 over or bigger injector

    I'm looking for a set of Exergy 100 over or bigger injectors. Could be as big as 350's. Looking for low milage injectors with good balance rates. Would also consider a set of exergy nozzles in 100's or bigger. Thanks a lot
  17. B

    Torque Converter lockup issues using lockup switch.

    I'm having some issues with my converter locking up while sled pulling. I have a dhd lockup switch. Converter will lockup right away as long as I'm turning under 3250 rpm. Any rpm about it it won't lock up. Any ideas before I pull my tranny. Truck has a full built engine s400 charger making...
  18. B

    2011 3500hd wheel spacers.

    Hey any one had any dealings with this ckmpnay and they're wheel spacers? http://www.motorsport-tech.com/dually.html I needed a set so I could use my stock aluminum wheels with my zone 5" lift. I ordered a set of 1.5" for the front and 3" for between my rear duals. They seem like they'd...
  19. B

    LML dually zone lift kit.

    I just picked up a 2013 3500hd Ltz dually to make a tow pig for lmm. Looking into putting a lift on it and 33-35's. I was looking at the zone 5". Is anyone running one? Did you have to use front wheel spacers to use 17" wheels and what needed to be done to use the rear blocks. I'm guessing I'll...
  20. B

    DHD axle tube reamer?

    Has anyone ever used the axle tube reamer from dhd? Might be a dumb question but do you use a drill or tap handle for it. and how long did it take you to ream each side?? Thanks a lot. Is there any companies that make a better one?
Top Bottom