Search results

Search the forum Search Articles
  1. NJ_LLY

    ring gap

    Since no real interest has been shown in buying my parts by anyone I figure I may as well put it together. I'm leaning towards forged pistons as the truck will see minimal street use a I was wondering what kind of ring gap I should have or are total seal rings the way to go?
  2. NJ_LLY

    V2 issue

    I recently bought a V2 off of a member to replace my V1 and am having issues connecting to my truck. I keep getting a code that says ERR_NOCABLE/31 but all cables are connected. If I disconnect the cable from the lap top I can power the V2 off of the truck and if I disconnect it from the truck I...
  3. NJ_LLY

    Factory main bolts

    Are factory main bolts reusable? I keyed the crank and am just putting the crank back in with the same bearings and want to be sure I don't need new bolts.
  4. NJ_LLY

    billet 480 in triples

    I have a billet 480 that I've been thinking about using as the top charger in a set of triples. My question is what would the exhaust side need to be? The setup will most likely be 480/472x2.
  5. NJ_LLY

    Coilovers

    Im going to be building a truck and am wanting to run coilovers in the front and a ladder bar with coilovers in the rear. Who is running this setup? What shocks are you using?
  6. NJ_LLY

    466/480 twins

    I'm looking into running this setup and was curious how those that currently run it like it. The 80 I have will have a bilet wheel and I may also add one to the 466.
  7. NJ_LLY

    SoCal cams

    What is the difference between the 3 af cams SoCal sells? My build may include one and I'm not sure which one to order.
  8. NJ_LLY

    Fingers pistons

    Besides Danville who else sells oval bowl pistons? I'm looking to put a set in my motor and wanted to shop around.
  9. NJ_LLY

    4" lift on 33's

    Does anyone have pictures of their 4" lifted truck on 33's? How does it ride? What did you do in the rear?
  10. NJ_LLY

    Engine tolerances

    Where can I find the tolerances and torque specs for the bottom end? I'm doing a stock over haul and need them.
  11. NJ_LLY

    Factory Bose amp

    I'm pretty sure my amp took a dump as the second I put the fuse it its full blast static. What are my options? Will an aftermarket radio rectify it or do I need to find an amp?
  12. NJ_LLY

    Valve springs

    Who else makes valve springs for our trucks besides hamilton and SoCal?
  13. NJ_LLY

    Injector size

    So I'm putting a motor together with 475/stock twins and duel pumps. I'm torn on injector size between 60, 80, and 100s. The truck is going to be my frequent driver as I do have a spare beater so it may tow from time to time. What would HP limits 60s and 80s? the truck may also end up with a...
  14. NJ_LLY

    Cost to paint the truck.

    How much would it cost to paint a cc/sb. It's black now but I want to do something different.
  15. NJ_LLY

    Winter time coolant temps

    Yesterday I was investigating my shit fuel economy and noticed that my coolant temps would not go over 160. That temp was after 2 different 50 mile trips. Is this normal or are the t-stats bad? Outside air temp was 25-35.
  16. NJ_LLY

    Internal harness o-ring

    Does anyone know the size of the o-ring for the main plug?
  17. NJ_LLY

    Nasty girl

    Whatever happened to Keith and nasty girl?
  18. NJ_LLY

    Trans kit tolerances

    I'm putting a kit that David sent me and don't know if the tolerances are supposed to be as factory or not. Also does anyone know what's with the extra clutch in the c4's. thanks. And yes I have tried calling him before posting.
  19. NJ_LLY

    Converter won't unlock

    Any one know what would cause a new converter to not unlock in a freshly built trans?
  20. NJ_LLY

    Harness pin removel tool

    I am going to be installing my dsp switch soon and want the rite tool for the rite job. does anyone know where this tool can be found or the cost of it?
Top Bottom