Search results

  1. M

    125k mile turbo junk?

    I got a 17 3500 that's throwing a p100b turbo code. It's all stock. We put a new actuator on it and same thing. Is this thing really going to need a turbo this early in life? Sent from my SM-N975U using Tapatalk
  2. M

    Iso lly fuel and air

    I have one I can run Sent from my SM-N975U using Tapatalk
  3. M

    Iso lly fuel and air

    I'm looking for a twin setup for my lly. I already have a s475 so prefer no turbo. Also looking for dual fueler. I have a good stock cp3 but would look at a modified stock or 10mm stroker pumps. Before I buy new thought I'd spend some stimmy money here if someone wanted to move some parts...
  4. M

    Lmm van parts

    I have a lmm from a van/transit bus. Going to pull all the outside stuff off to put my lbz stuff on when it goes in my truck. Thought I would offer the parts to anyone on here before I junk them. Have to have a price so how bout this: Harness $150 Accessories $250 Air intake/coolant plumbing...
  5. M

    Lbz swap in

    It was a fleet van from Memphis Tennessee. Suppose to have been maintained regularly. Rite at 200k miles on the unit. Sent from my SM-N975U using Tapatalk
  6. M

    Lbz swap in

    I probably have a few driver side manifolds from lml that I could put on. Yea I want to do a few things to help it run better while its out. But I dont want to tear it down and do head studs and gaskets yet. Unless I put it in and it goes to pushing water. The rig has been down over a year...
  7. M

    Lbz swap in

    Hey guys I toasted my 330k mile 06 lly/lbz back last year. So finally after gathering parts and planing to build a motor I have picked up a complete lmm to just put back in and go. I would like some input/suggestions on what I need to look at doing while its out as far as parts that are easier...
  8. M

    Complete motors, trans, and parts

    How about that 08 van engine? Lmm? Miles? Issues? Sent from my SM-N975U using Tapatalk
  9. M

    Engine parts

    Central Arkansas Sent from my SM-N975U using Tapatalk
  10. M

    AF cam or trade for stock?

    I am looking for a new or lightly used AF cam that doesn't require any piston machining. I have a stock keyed cam that I'd throw in trade or like to buy out rite. Thought I'd ask here before I buy new. Truck will be a tow/daily driver. No racing no crazy hp. Just a good reliable 500-600 hp...
  11. M

    Lbz s&s 60% and fleece 10mm

    What kinda money on injectors? Sent from my SM-N975U using Tapatalk
  12. M

    Engine parts

    Just wondering guys. Am I to high? Sent from my SM-N975U using Tapatalk
  13. M

    Engine parts

    Gauging interest in my parts to build a short block. Lb7/lly standard bore block new cam bearings Arp main studs new Dhd stock crank keyed Dhd stock cam keyed Dhd delipped lb7 pistons (was run in a test motor then pulled out) Lbz rods Crank, rods, pistons balanced with fluid damper and bd...
  14. M

    lmm fuel knock misfire

    Sorry guys just seen this. I havent had any break through. Just talked to customer the other day (yes 3 years of sitting here while hes been in and out of jail/hospital/etc...) he threw a fit and said he wouldnt pay any bills towards the truck since it's not fixed. Pushed it back in the shop...
  15. M

    WTB: Lbz injectors

    You want to sell your 60s? Sent from my SM-G892A using Tapatalk
  16. M

    Allison 5sp: Air Flow parts recommendations

    I bought the oil supply and drain kit. Then the exhaust down pipe. So I dont have a full kit for the install. Just thought these might be good items to add when I do the install(manifolds and up pipes that is) Thanks Sent from my SM-G892A using Tapatalk
  17. M

    Allison 5sp: Air Flow parts recommendations

    I have a lly that I'm going to put 100% over injectors, 10mm pump and S369 turbo on. Looking for recommendations on y-bridge, manifolds and up-pipes Thanks Sent from my SM-G892A using Tapatalk
  18. M

    Allison 5sp: 3500 drw lift and tire/wheel question

    I already have the ucas and my upper ball joints are close to needing replaced. Plan to do the fabtech tierods to upgrade them over the stock when I do this. The truck is a work truck. I only use it offroad when working on the farm or jobsites. No wheeling. But I'd like to go to 34-35" tire...
  19. M

    Allison 5sp: 3500 drw lift and tire/wheel question

    I have a 06 3500 drw. I'm about to swap front differentials due to a gear change. I'm leveled now with 295s on my stock steel wheels. I'm looking for opinions and feedback on wether to just leave it like it is (doesnt wear the front tires funny and drives good rides good) or put a 4-6" lift on...
  20. M

    lmm fuel knock misfire

    from what i just checked i don't think the crank is broke as i can put the flywheel holding tool in the trans and turn the crank back and forth. it moves just a little then stops when the tool takes up the slack on the teeth. unless someone thinks of another way to check it.