Search results

  1. R

    lb7 dsp5 help

    alright thanks for the tips, havent had any issues till the lb7 haha
  2. R

    lb7 dsp5 help

    did full flash again and bricked ecm so that was great haha got new one going to use the stock file on it and go from that hopefully solve the issues
  3. R

    lb7 dsp5 help

    alright ill give it a go again, checked switch wiring and its good
  4. R

    lb7 dsp5 help

    did do full flash but it loaded the tunes pretty fast ( it was under 40sec) my lly takes at most a minute or two also logged and it doesnt show that its changing this truck did have a bully dog tuner on it and wasnt able to remove that bully dog file back to stock but i dont think thats going...
  5. R

    lb7 dsp5 help

    hey, have a lb7 that is stock has ppe boost valve and exhaust, i have the switch installed the led lights up green on the back i pulled the stock file off truck updated it to dsp5 followed steps made the tunes saved, loaded in the truck and the switch doesnt work, efilive shows no voltage on...
  6. R

    lly triples

    alright thx for the input, going twins
  7. R

    lly triples

    what would be the power potential with the smaller 3794
  8. R

    lly triples

    hey, im putting together a built motor (1000hp+)for my lly and im thinking about going to triple turbos vgt/s300's cause everyone does twins so want to change it up the vgt turbo i have now is a 68mm 3794 i am wondering what would be the best setup for daily/race, iam building the kit my self...
  9. R

    diamond forged .020 pistons

    blowby im ok with it has alittle bit now as it is lol, if i can get 20k-25k kms out of them that will take 3 years or more by then the truck will be rutted out again anyway from being in canada
  10. R

    diamond forged .020 pistons

    have talked with diamond they do recommended a .006-.007ptw for the pistons
  11. R

    diamond forged .020 pistons

    alright thx
  12. R

    diamond forged .020 pistons

    alright sounds like a non issue for me to worry about, ill just tighten wall clearance up to .003-.004 over building it for my needs, planning for future upgrades
  13. R

    diamond forged .020 pistons

    in the middle of collecting parts for a lly motor build, question i have is how much daily driving can be done on a set of forged pistons piston/wall clearance is .006-.0065 power goal of a 1000hp and daily around 800hp got a good deal on forged pistons only reason for going that route
  14. R

    lly 100% injector tune help

    thx pilot table helped a lot to quiet down, just new delipped lb7 pistons and carrilo rods
  15. R

    lly 100% injector tune help

    hey guys I need a hand tuning my 100 over injectors first the tuner I had tuning my truck cant sell or retune anymore do to all the new rules and epa coming down on everyone. ok Im starting out with his base tune for my truck with 60% over in it I have got it to idle fine now with a little...
  16. R

    Trans issues

    have a ppe stage 5 kit with the same issues everything new, clearances good, takes 2-3 sec. to shift to reverse then slams, forward is smooth, 1-2 hard,2-3 hit and miss(hard sometimes),3-4-5 smooth, 3-2-1 down shifts are hard parked it got tired of missing with it, let me kno what fixed it :mad:
  17. R

    LLY-tune

    just wondering if someone could look at my tune let me kno your thoughts on it, try it if u want I have ran it let me kno thanks
  18. R

    02 rebuilt trans issues

    ya i understand, was hoping for a starting point to look at thx
  19. R

    02 rebuilt trans issues

    put all new solenoids in, cleaned valvebody and half the issues are gone, now it shifts fine into drive and shifts in and out of all the gears ive reset the trans with flashscan, I still have issues with reverse with it banging in to gear and no codes have popped up my question is what...