Search results

  1. ikeG

    LB7 build

    *.020". Looks like a good time Sent from my SM-G960U1 using Tapatalk
  2. ikeG

    LML engine knock

    It was owned by a dealership. They sold it. Explained the concern to the customer and everything. Never heard back Sent from my SM-G960U1 using Tapatalk
  3. ikeG

    LML engine knock

    Never found an issue. Still made the noise Sent from my SM-G960U1 using Tapatalk
  4. ikeG

    Seriously?

    It ended up having the wrong rotors. There is 3 different rotor part numbers for it, depending on the hub it came with. The depth of the back space is the difference, these washers kept the incorrect rotor from rubbing the knuckles. Sent from my SM-G960U1 using Tapatalk
  5. ikeG

    Seriously?

    Older jeep cherokee in recently. Nice surprise. Sent from my SM-G960U1 using Tapatalk
  6. ikeG

    Twins with Twins, Anyone?

    Assuming turbo shaft speed skyrocketed during the freerev, the turbo can't really be blamed. That has to be a large issue with turbos on boats? When they props come out of the water theirs really nothing you can do. Sent from my SM-G960U1 using Tapatalk
  7. ikeG

    Promaxx Heads - Thoughts?

    Linco diesel may have reman stock heads ready to go. Sent from my SM-G960U1 using Tapatalk
  8. ikeG

    Converter change

    Its never towed with this setup, and will not be able to until engines been repaired. I know there are now certainly better options than the 1058 for other applications. Hate to decide to try a different converter after engines back in but that may be what has to happen Sent from my...
  9. ikeG

    Converter change

    I got a guy that has had his needs change with his current LBZ. Its a S472/83/1.0 single truck with a stock cp3 and 40% nozzles. Built trans with a 1058. No towing needs until recently. He will occasionally need to move a piece of equipment short distances, gross trailer weight around 16k. The...
  10. ikeG

    4L60E diagnostic help

    I replaced the suspect tcm connector pin but no change. As soon as atf gets warm, it trips P2764. Pulled it back in, solenoid ohms out fine again. Checked it for a short to trans case with truck harness plugged into trans connector, bingo. Tcc pwm circuit was rubbed through on top of trans where...
  11. ikeG

    4L60E diagnostic help

    Solenoid ohms out at 10.5. I think I found a spread pin in the tcm connector. Waiting on a replacement. Sent from my SM-G960U1 using Tapatalk
  12. ikeG

    4L60E diagnostic help

    Test light stays lit with tcc on or off. That indicates bad tcm. But my snap on scantool only allows me to turn tcc on or off, no 0 to 100%. When I turn tcc on, duty pid goes to 99%. When I turn it off, duty goes to 0%. I can command tcc on while driving and it works. The circuits themselves ohm...
  13. ikeG

    4L60E diagnostic help

    Ok thanks mike Sent from my SM-G960U1 using Tapatalk
  14. ikeG

    4L60E diagnostic help

    Its a reman trans, 3k on it. 165k on the tcm. Once the trans is warm, it trips that code after clearing just sitting in the driveway. The reman trans company doesn't want to give me a solenoid and such until external circuits are ruled out. Which, using prodemand instructions, points to the...
  15. ikeG

    4L60E diagnostic help

    How about an 09 Silverado 1500 2wd that sets P2764(TCC Pressure Control Solenoid Low Voltage) every time it gets up to temp. Runs like a top until it reaches around 170 deg, then trips the code and goes into fail safe mode. Using Mitchells diag instructions, it points to the TCM. But i am...
  16. ikeG

    LML Wiring ID this wire - ANSWERED- Thanks

    Turbo vane position sensor Sent from my SM-G960U1 using Tapatalk
  17. ikeG

    2011 lml Duramax overfueling

    It does sound like the symptoms that come up if someone leaves their egr valve and egr cooler bypass valve plugged in after exhaust removal Sent from my SM-G960U1 using Tapatalk
  18. ikeG

    Classic Prices-WTH???

    https://bringatrailer.com/listing/2005-chevrolet-silverado-16/ Sent from my SM-G960U1 using Tapatalk
  19. ikeG

    Converter change / rebuild

    Goerend always treated me like gold. They have reman'd probably 6 of their G's for me. They have even refreshed a Suncoast 1053 for me, using Suncoast parts i believe. Sent from my SM-G960U1 using Tapatalk
  20. ikeG

    15.5+ fan shrouds.

    I agree 1000%. Man I've nearly designed a new language while trying to re install the fan and shroud. I am only able to leave the thin primary piece of the shroud on the rad when picking cabs. Sent from my SM-G960U1 using Tapatalk