Recent content by wilsondiesel

  1. wilsondiesel

    Transmission issues?

    Hey Mike I called and left a message. This problem seems to be pretty inconsistent. Customer seems to think it is related to the tune we put on but I am thinking just a coincidence
  2. wilsondiesel

    Transmission issues?

    Hey Mike, is there a way in these transmissions to tell if it’s sticking valves without pulling the valve body apart? It is not throwing any transmission codes.
  3. wilsondiesel

    Transmission issues?

    Could you send me a screenshot of where to air check after removing the valve body? That would be the best way to check for a damaged reverse piston correct? Do you usually clean the valve bores like and Allison to unstick valves or just replace the whole valve body? Thank you for the info as I...
  4. wilsondiesel

    Transmission issues?

    Has anyone seen transmission issues out of these? I have a customer that has a 2016, is having issues of no reverse engagement when parked on a hill. Fluid level and pressures are good. No codes. Truck is deleted are the only mods
  5. wilsondiesel

    Filled Block w/ Stock Heads?

    Thank you for tagging that thread. I’d be interested in a used set of cast iron heads if found any worth the money
  6. wilsondiesel

    Filled Block w/ Stock Heads?

    I knew you would be the one to know! Would I have to run water through the heads is my biggest question? Currently still run a valley mount charger so would have to run a remote mount with forward facing manifolds so didn’t have up pipes in the way of the coolant ports on back of the heads. Was...
  7. wilsondiesel

    Filled Block w/ Stock Heads?

    Has anyone ran a dry/filled block along with running factory aluminum casting heads? It would be in a pulling engine so would not have much run time except a few minutes going down the track.
  8. wilsondiesel

    Which T-case to use?

    Following, I am interested to know as well, as I’m building a gutted 2.6 pull truck but only have 263xhd cases around
  9. wilsondiesel

    Edge Pulsar

    On my Beta unit I don’t know of a direct adjustment that you can do, other than with the increase of the power level, I noticed an increase in pedal sensitivity
  10. wilsondiesel

    Edge Pulsar

    Yes, I did notice a couple mpg increase in fuel economy cruising around town on level 5. There where a couple bugs with the module, like a slight miss at idle everyone and then, but edge has taken care of that in the new flash for the unit, which will be the same flash as the production unit. I...
  11. wilsondiesel

    Which forged piston??

    Thanks everyone for the input, leaning towards Mahle forged for my application.
  12. wilsondiesel

    Which forged piston??

    I’m building a lb7 sled pull engine this winter with a partial filled block and I’m having a hard time deciding between Mahle Forged, Fingers Mahle Forged, Ross pistons or CP. is Aries owned by CP now? Or are there any other brands I should look into? Diamond is a little rich for my blood. From...
  13. wilsondiesel

    LML Callies Durastar Crankshaft Issues??

    Yes going to run an lb7 block, stock main caps, with main studs.
  14. wilsondiesel

    LML Callies Durastar Crankshaft Issues??

    Me-max, what crank are you running in your truck? This will be in a partial filled block, 2.6 sled pull truck. I have a fluid dampener I plan to run. Haven’t decided which rod or piston yet, but pistons will be forged. Sorry for derail
  15. wilsondiesel

    LML Callies Durastar Crankshaft Issues??

    Okay, only thing is I don’t know the history on this crank on how it was ran before I got it, but if it checks out okay at the machine shop then I should be okay? Are you running main studs?
See more
Top Bottom