Recent content by mamumtsllc

  1. M

    125k mile turbo junk?

    I got a 17 3500 that's throwing a p100b turbo code. It's all stock. We put a new actuator on it and same thing. Is this thing really going to need a turbo this early in life? Sent from my SM-N975U using Tapatalk
  2. M

    Iso lly fuel and air

    I have one I can run Sent from my SM-N975U using Tapatalk
  3. M

    Iso lly fuel and air

    I'm looking for a twin setup for my lly. I already have a s475 so prefer no turbo. Also looking for dual fueler. I have a good stock cp3 but would look at a modified stock or 10mm stroker pumps. Before I buy new thought I'd spend some stimmy money here if someone wanted to move some parts...
  4. M

    Lmm van parts

    I have a lmm from a van/transit bus. Going to pull all the outside stuff off to put my lbz stuff on when it goes in my truck. Thought I would offer the parts to anyone on here before I junk them. Have to have a price so how bout this: Harness $150 Accessories $250 Air intake/coolant plumbing...
  5. M

    Lbz swap in

    It was a fleet van from Memphis Tennessee. Suppose to have been maintained regularly. Rite at 200k miles on the unit. Sent from my SM-N975U using Tapatalk
  6. M

    Lbz swap in

    I probably have a few driver side manifolds from lml that I could put on. Yea I want to do a few things to help it run better while its out. But I dont want to tear it down and do head studs and gaskets yet. Unless I put it in and it goes to pushing water. The rig has been down over a year...
  7. M

    Lbz swap in

    Hey guys I toasted my 330k mile 06 lly/lbz back last year. So finally after gathering parts and planing to build a motor I have picked up a complete lmm to just put back in and go. I would like some input/suggestions on what I need to look at doing while its out as far as parts that are easier...
  8. M

    Complete motors, trans, and parts

    How about that 08 van engine? Lmm? Miles? Issues? Sent from my SM-N975U using Tapatalk
  9. M

    Engine parts

    Central Arkansas Sent from my SM-N975U using Tapatalk
  10. M

    AF cam or trade for stock?

    I am looking for a new or lightly used AF cam that doesn't require any piston machining. I have a stock keyed cam that I'd throw in trade or like to buy out rite. Thought I'd ask here before I buy new. Truck will be a tow/daily driver. No racing no crazy hp. Just a good reliable 500-600 hp...
  11. M

    Lbz s&s 60% and fleece 10mm

    What kinda money on injectors? Sent from my SM-N975U using Tapatalk
  12. M

    Engine parts

    Just wondering guys. Am I to high? Sent from my SM-N975U using Tapatalk
  13. M

    Engine parts

    Gauging interest in my parts to build a short block. Lb7/lly standard bore block new cam bearings Arp main studs new Dhd stock crank keyed Dhd stock cam keyed Dhd delipped lb7 pistons (was run in a test motor then pulled out) Lbz rods Crank, rods, pistons balanced with fluid damper and bd...
  14. M

    lmm fuel knock misfire

    Sorry guys just seen this. I havent had any break through. Just talked to customer the other day (yes 3 years of sitting here while hes been in and out of jail/hospital/etc...) he threw a fit and said he wouldnt pay any bills towards the truck since it's not fixed. Pushed it back in the shop...
  15. M

    WTB: Lbz injectors

    You want to sell your 60s? Sent from my SM-G892A using Tapatalk