Search results

Search the forum Search Articles
  1. Wikid

    LBZ: Rough Idle

    Hey guys, Recently I was working on my truck to fix a small fuel leak to the CP3 from the lift pump. When i got it all said and done fired the truck up but had the MAF sensor unplugged and the engine threw a bunch of DTCs one of which disabled the FPRV in the CP3 causing the rail pressure...
    • Wikid
    • Thread
    • Replies: 0
    • Forum: LBZ
  2. Wikid

    LBZ: Cold side intercooler boot

    Hey guys so going to the gym today and got on it to get on the freeway and my lower intercooler boot the plastic one with the retaining clip that goes onto the intercooler blew off with the retaining ring and all. Marred up the retaining ring groove pretty good on my Mishimoto intercooler in the...
    • Wikid
    • Thread
    • Replies: 2
    • Forum: LBZ
  3. Wikid

    EGT probes

    What EGT gauge and or probes are you guys using? I keep having issues with my Edge CTS EGT probe. so I just want to go to something more reliable but would like something with an alarm or light. I would like to use something from auto meter if possible as my boost and drive pressure gauges are...
  4. Wikid

    Nitrous Tuning?

    I am thinking of adding a 50-100HP shot of nitrous to my build. I am curious if it is necessary to have a tune done specifically for the nitrous? I know gas motors you want to remove timing I would think diesels would also need some adjustment in the injection timing area to make them last...
  5. Wikid

    LBZ: MAP sensor Upgrade?

    Hey guys, So I have seen a few posts regarding MAP sensors on built trucks but couldn't find info on upgrading them specifically. Since I am running a 80mm over 68mm which easily gets up to 55 PSI. Should I upgrade my MAP sensor, if so to what? what reason does it need to be upgraded? Wikid
    • Wikid
    • Thread
    • Replies: 0
    • Forum: LBZ
  6. Wikid

    Remote Oil line for valley turbo

    Hey guys, anyone ever have issues with these remote oil line kits and their crimped connections leaking? I have a fleece one and the crimped on AN fittings is leaking pretty good now. I contacted them but with it being the holidays I wont be able to do anything till next week. Wikid
  7. Wikid

    Alternator bad?

    Hey guys, so driving home today my DIC came on saying battery not charging. So i got home checked all the usual stuff, reseated the plug on the alternator checked everything with a volt meter didnt really get any alarming reading other than wasnt sure what I should be seeing on the plug that...
    • Wikid
    • Thread
    • Replies: 5
    • Forum: LBZ
  8. Wikid

    LBZ: EDGE CTS acting odd

    So the new motor has been running great but not its about finding all the little gremlins in the truck from when it was sitting for 6 months and during install. I have noticed that my Edge will turn on when I remotely unlock my doors. I replaced my EDGE EGT probe and they sent me a new one...
  9. Wikid

    Ideal lift pump pressures

    Hey guys, So if anyone has followed my project cracked piston build, I got it started up recently. It started without any issues warmed up and drove around fine. Some background on the system. Sump from the fuel tank to -8 to AD2-165 then -8 to 12mm cp3 The return is -6 from the cp3 to a...
  10. Wikid

    LBZ: First start, which fuse to pull?

    Hey guys im about to fire up my new motor but wanted to build some oil pressure first. On an lbz what is the best fuse to pull so it wont fire. I kept seeing ficm to be pulled but i dont have a fuse labeled that in my fuse box. Sent from my SAMSUNG-SM-G930A using Tapatalk
  11. Wikid

    kryptonite race centerlink with heims

    Hey guys, so I ordered the a new steering setup for my truck since the motor was out and figured it would be much easier to replace. However I wanted to get the SS version of this but they sent the wrong version. My motor gets here next week so I would have to wait to install the motor if I...
  12. Wikid

    LBZ: Project "Cracked Piston"

    I have mostly roamed around these forums for the past 3 years but never really posted anything. Since this is a large build I wanted to throw it on here. So I've had my truck about 3 years, when i bought it the owner already had a lift pump, traction bars, and Snow Perf W/M injection. 3...
  13. Wikid

    Plumbing from Lift to CP3

    Hey guys, My motor is out getting machined on and I am going to be upgrading almost everything on the motor. I wanted to remove the current fuel block and plumb my CP3 directly. I can just run a -8 line straight from my LP to the CP3 correct, no need to tie it into the return? I only ask...
Top Bottom