Duramax Diesels Forum Truck of the Week


Go Back   Duramax Diesels Forum > Search Forums

Showing results 1 to 25 of 500
Search took 0.02 seconds.
Search: Posts Made By: 2004LB7
Forum: Forum Suggestion Box Today, 10:03 PM
Replies: 4
Views: 59
Posted By 2004LB7
The little square box with the picture of a...

The little square box with the picture of a mountain. This will ask you for a link of the picture

The picture already needs to be online somewhere viewable. This can be another website, a photo...
Forum: LB7 Yesterday, 04:39 PM
Replies: 77
Views: 4,611
Posted By 2004LB7
This is the image I get reading that :roflmao: ...

This is the image I get reading that :roflmao:
http://www.rps.org/~/media/Albums/2016/October/20/Physical%20Artistry%20512367/0974%20%20Tightrope%20Unicyclejpg.ashx
Forum: LB7 Yesterday, 12:44 PM
Replies: 77
Views: 4,611
Posted By 2004LB7
How about these? ...

How about these?

https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F253175385858
...
Forum: LB7 06-17-2018, 08:03 PM
Replies: 77
Views: 4,611
Posted By 2004LB7
Well you did purchase the one from...

Well you did purchase the one from Pensacola:roflmao:
Forum: LB7 06-17-2018, 07:10 PM
Replies: 77
Views: 4,611
Posted By 2004LB7
Here is a picture of the tool I made. Nothing...

Here is a picture of the tool I made. Nothing fancy. Just some one inch EMT and connector

The one on the left is the first one I made but it didn't grip too well. I made the one on the right when...
Forum: LB7 06-17-2018, 06:03 PM
Replies: 77
Views: 4,611
Posted By 2004LB7
I know very well of that little ball he is...

I know very well of that little ball he is referring to. By the way, that thread of the injector disassembly is my thread and those are my photos.

Yes, if you drop the ball good luck finding it....
Forum: LB7 06-17-2018, 10:32 AM
Replies: 77
Views: 4,611
Posted By 2004LB7
I swapped out three on my LB7. Ran great with...

I swapped out three on my LB7. Ran great with good balance rates after.

Keep all of the small parts, etc below the solenoid in place and only swap the coil. After unscrewing the solenoid,...
Forum: LB7 06-17-2018, 09:50 AM
Replies: 77
Views: 4,611
Posted By 2004LB7
If I where you I would cancel that order. Do a...

If I where you I would cancel that order. Do a search here and read all about Pensacola's "great" injectors. Save yourself the pain and get em from LDS. They are also a vendor here

At a minimum,...
Forum: Duramax Hard Parts 06-17-2018, 08:54 AM
Replies: 6
Views: 179
Posted By 2004LB7
I just use the fuel hose from the auto parts...

I just use the fuel hose from the auto parts store. Never had any issues with them
Forum: LB7 06-17-2018, 08:02 AM
Replies: 77
Views: 4,611
Posted By 2004LB7
Is that right at the injector? Or on the harness...

Is that right at the injector? Or on the harness somewhere?

Its good you found something as now you can get it fixed
Forum: LB7 06-16-2018, 06:52 PM
Replies: 77
Views: 4,611
Posted By 2004LB7
Unplug the connector on the fcim. Prob the pins...

Unplug the connector on the fcim. Prob the pins there going to the injectors
Forum: LB7 06-16-2018, 05:09 PM
Replies: 77
Views: 4,611
Posted By 2004LB7
So passenger side, it sounded like you were...

So passenger side, it sounded like you were working on the drivers side on an earlier post
Forum: LB7 06-16-2018, 05:08 PM
Replies: 77
Views: 4,611
Posted By 2004LB7
The FCIM does step up the voltage to 96 volts but...

The FCIM does step up the voltage to 96 volts but only for a split second to open the injectors. You would need to put a scope on it to read the voltage at it will be a pullsed signal. I think the 96...
Forum: LB7 06-16-2018, 01:18 PM
Replies: 77
Views: 4,611
Posted By 2004LB7
Here's a thought for Tylerrc34 Is your codes...

Here's a thought for Tylerrc34

Is your codes for injector 1, 3, 5 & 7? Or 2, 4, 6 & 8?

The original poster had codes for the injectors on the passenger side but I see that you have the drivers...
Forum: LB7 06-16-2018, 12:06 PM
Replies: 77
Views: 4,611
Posted By 2004LB7
I bet you are right Tom I was just thinking...

I bet you are right Tom

I was just thinking of a few last steps to do that dont cost anything before braking down for an FCIM. The codes listed could be a number of things, one of which is a...
Forum: Mike L's Trans Talk 06-16-2018, 10:48 AM
Replies: 16
Views: 489
Posted By 2004LB7
2x what was just said A transgo jr, while...

2x what was just said

A transgo jr, while not a built transmission, it will help it live just a little bit longer. I would stick with a 40 HP tow tune until you are ready to have the transmission...
Forum: LB7 06-16-2018, 10:41 AM
Replies: 77
Views: 4,611
Posted By 2004LB7
I would put it all back together less the upper...

I would put it all back together less the upper valve covers and test the connections at the fcim. If all looks good test run it. If it still has issues take the ohm readings that the fcim connector...
Forum: LB7 06-16-2018, 09:40 AM
Replies: 77
Views: 4,611
Posted By 2004LB7
Did you check the injector pigtails that run...

Did you check the injector pigtails that run through the valve covers?
Forum: Mike L's Trans Talk 06-16-2018, 08:44 AM
Replies: 16
Views: 489
Posted By 2004LB7
Just put a block of wood under the go pedal so...

Just put a block of wood under the go pedal so you can only go half throttle :roflmao:
Forum: Mike L's Trans Talk 06-15-2018, 11:31 PM
Replies: 16
Views: 489
Posted By 2004LB7
Just start putting money aside for a rebuild a...

Just start putting money aside for a rebuild a few years down the road. If you are nice to it, and maybe a little luck, it will last just long enough for you to have the money needed to get it built....
Forum: LB7 06-14-2018, 11:29 AM
Replies: 77
Views: 4,611
Posted By 2004LB7
Also, to elaborate a little bit on what LBZ said....

Also, to elaborate a little bit on what LBZ said.

There shouldn't be any continuity between the injector studs and ground. It should read in the megaohms. Stud to stud is something like a half an...
Forum: LB7 06-14-2018, 10:24 AM
Replies: 77
Views: 4,611
Posted By 2004LB7
I disconnected the connection right at the valve...

I disconnected the connection right at the valve covers for the injectors and measured there. There are four pins. It should be obvious but two go to one injector and the other two go to another...
Forum: LB7 06-13-2018, 09:38 PM
Replies: 77
Views: 4,611
Posted By 2004LB7
I had three solenoids short out on me over the...

I had three solenoids short out on me over the time i had my LB7

First one I ended up replacing it with a new one for the dealership

2nd, and 3rd, I ended up purchasing a few used injectors on...
Forum: Duramax Tuning, Logging, and Gauges 06-13-2018, 09:18 PM
Replies: 14
Views: 456
Posted By 2004LB7
Windows 7, the last good os from Microsoft ...

Windows 7, the last good os from Microsoft

8, 8.1 & 10 are horrible for someone trying to get actual work done. Good for wasting time and playing around but not productive

XP and 7 are the...
Forum: Smoke Signals 06-13-2018, 07:53 AM
Replies: 23
Views: 515
Posted By 2004LB7
Back on track, haha I sold my 2004 LB7 ex/sb...

Back on track, haha

I sold my 2004 LB7 ex/sb with a built transmission and injectors done about two years earlier with somewhere around 150k miles on it for $11k

Anything more and I had no...
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -7. The time now is 10:21 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
vB.Sponsors