Duramax Diesels Forum Truck of the Week


Go Back   Duramax Diesels Forum > Search Forums

Showing results 1 to 25 of 500
Search took 0.01 seconds.
Search: Posts Made By: rcr1978
Forum: Turbo Talk Yesterday, 04:42 PM
Replies: 44
Views: 2,690
Posted By rcr1978
What did you end up with on the valley charger? I...

What did you end up with on the valley charger? I got that you went with a SXE 64.5 was it the big turbine and 1.0 housing?
Forum: Smoke Signals 02-12-2018, 11:31 PM
Replies: 5,725
Views: 490,924
Posted By rcr1978
I think mines hurt and I have the solenoid mod,...

I think mines hurt and I have the solenoid mod, mines not even max effort. It's max on the factory fuel system with no lift pump. 2nd-4th lots of rpm with not a whole lot of go anymore and that's in...
Forum: Duramax Tuning, Logging, and Gauges 02-11-2018, 08:09 AM
Replies: 2
LBZ: Baro & MAP
Views: 289
Posted By rcr1978
The baro sensor is in the ecm and I wouldn’t be...

The baro sensor is in the ecm and I wouldn’t be to worried about it. If you live in a area were the elevation doesn’t change much more than 3500ft I would just tune your timing and boost tables so...
Forum: Mike L's Trans Talk 02-09-2018, 07:59 AM
Replies: 17
Views: 613
Posted By rcr1978
Did you ban him ? :roflmao:

Did you ban him ? :roflmao:
Forum: Mike L's Trans Talk 02-06-2018, 09:01 AM
Replies: 7
Views: 288
Posted By rcr1978
That's what I was looking for :D Some of there...

That's what I was looking for :D Some of there stuff is not bad the F spring I've seen worn a few times though maybe that may be better but I will stick with OEM.
Forum: Mike L's Trans Talk 02-06-2018, 08:20 AM
Replies: 7
Views: 288
Posted By rcr1978
Sonnax Trim valve and spring kit

I was looking through Sonnax's stuff and found this https://www.sonnax.com/parts/2121-trim-valve-spring-kit

Sure looks similar to the transgo kit except the little springs and check balls, unless...
Forum: LB7 02-02-2018, 09:44 PM
Replies: 32
Views: 956
Posted By rcr1978
Ball and seat is under the solenoid, nozzles will...

Ball and seat is under the solenoid, nozzles will do nothing for that. The ball and seat cause high return rates. Worn nozzles cause leaky injectors/overfueling/idle haze.

Just buy new to much...
Forum: Transfer Case / Axles / Driveshafts Tech 02-02-2018, 09:38 PM
Replies: 9
Views: 384
Posted By rcr1978
Not sure about the input bearing but the couple...

Not sure about the input bearing but the couple of pump upgrades I have done I also had to move the output shaft back for the snap ring to go in.
Forum: Duramax Engine Building 02-02-2018, 09:06 PM
Replies: 20
Views: 921
Posted By rcr1978
I went with a Callies/Wagler Stage 1 , didn't...

I went with a Callies/Wagler Stage 1 , didn't want to loose any drive-ability trucks going to be a multipurpose one not a dedicated racer/puller. Haven't tested yet motors still on the stand :o need...
Forum: Chassis & Suspension 01-29-2018, 07:48 AM
Replies: 2
Views: 156
Posted By rcr1978
You can just get 2” blocks for the rear and lower...

You can just get 2” blocks for the rear and lower the front that’s what I did and have the exact same lift. Went from 315/70/17 to 285/70/17 tires my wheels are 10” wide. Just bought 295/70/17 this...
Forum: EFILive 01-23-2018, 07:06 AM
Replies: 29
Views: 1,303
Posted By rcr1978
EfiLive just released some more tables for boost...

EfiLive just released some more tables for boost control. I know one works a little because I've had decent luck with it using a cax file. But there are others that I have not tried that look...
Forum: Chassis & Suspension 01-20-2018, 10:08 AM
Replies: 13
Views: 354
Posted By rcr1978
He's likely looking for decent CV angles and...

He's likely looking for decent CV angles and decent steering geometry hence lowering the 6" lift instead of cranking a 4"
Forum: Duramax Tuning, Logging, and Gauges 01-14-2018, 08:54 PM
Replies: 6
Views: 234
Posted By rcr1978
There is aftermarket ECM for LMM's that I bet has...

There is aftermarket ECM for LMM's that I bet has live tuning but I have no personal experience because it's to much $$$$ for me and I can get by with a stocker.
...
Forum: Mike L's Trans Talk 01-08-2018, 07:28 AM
Replies: 15
Views: 1,987
Posted By rcr1978
Bumping this up, just ordered a tech2 and candi...

Bumping this up, just ordered a tech2 and candi module because i'm not sure EFILive is getting the job done for the fast learn. Anyone ever see these change after setting them to fast learn and...
Forum: The Tool Crib 01-07-2018, 10:19 AM
Replies: 143
Views: 15,482
Posted By rcr1978
I procrastinated long enough and ordered the...

I procrastinated long enough and ordered the Tech2 and candi module from Sictools, can anyone confirm the Tech2 does a better job than EFILive for reseting taps? I have tried both full flashing with...
Forum: Mike L's Trans Talk 12-16-2017, 10:09 PM
Replies: 71
Views: 4,394
Posted By rcr1978
That's good news :D

That's good news :D
Forum: Mike L's Trans Talk 12-12-2017, 10:34 PM
Replies: 6
Views: 588
Posted By rcr1978
I just got the Billet P2 planet and hub set with...

I just got the Billet P2 planet and hub set with a input shaft looks good :D

Sure hope it's good :spit:
Forum: Duramax Engine Building 12-03-2017, 12:29 AM
Replies: 83
Views: 12,381
Posted By rcr1978
Lb7 piston squirters are .063" and open at 25psi,...

Lb7 piston squirters are .063" and open at 25psi, LML are .083" and open at 30psi.
Forum: Duramax Engine Building 12-02-2017, 12:49 AM
Replies: 83
Views: 12,381
Posted By rcr1978
Adding some new found info: LML oil pump press...

Adding some new found info: LML oil pump press relief valve pops at 88psi and reseats at about 66-68psi.
LML oil pump gears are the same diameter and tooth count as the previous years, the gears are...
Forum: Duramax Hard Parts 12-02-2017, 12:18 AM
Replies: 29
Views: 4,908
Posted By rcr1978
Think I saw Wagler made the switch to Fluidampr...

Think I saw Wagler made the switch to Fluidampr also.
Forum: Fingers 412-638-9026 11-25-2017, 07:26 AM
Replies: 12
Views: 960
Posted By rcr1978
This one yours then? I would like to see the...

This one yours then? I would like to see the tops, kinda weird only the sides split and they didn't blow through.
Forum: Mike L's Trans Talk 11-21-2017, 08:13 PM
Replies: 19
Views: 1,225
Posted By rcr1978
I just tore apart my trans I put together in 06...

I just tore apart my trans I put together in 06 with a SC4 kit. C2's (8 frictions) were trashed clutches were smoked it had a .140" clearance from the .070" it started at. C3's were burned but not...
Forum: Duramax Tuning, Logging, and Gauges 11-19-2017, 05:21 PM
Replies: 7
Views: 438
Posted By rcr1978
Dave there is some nice spreadsheets in there...

Dave there is some nice spreadsheets in there thanks!
Forum: Duramax Engine Building 11-08-2017, 04:35 AM
Replies: 19
Views: 933
Posted By rcr1978
I guess that's not to bad then what do you think...

I guess that's not to bad then what do you think you had for mileage on them roughly?

Sent from my SAMSUNG-SM-G891A using Tapatalk
Forum: Duramax Engine Building 11-07-2017, 10:01 PM
Replies: 19
Views: 933
Posted By rcr1978
What kind of life did you get out of them and...

What kind of life did you get out of them and roughly what hp?

Sent from my SAMSUNG-SM-G891A using Tapatalk
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -7. The time now is 06:40 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
vB.Sponsors